User manual SHARP VC-782S

[. . . ] Please refer to the relevant laws in your country. G No part of this publication may be reproduced, stored or transmitted in any form without prior permission from SHARP Electronics (Europe) GmbH. ® and PlusCode ® are registered trademarks of Gemstar Development G Corporation. G system is manufactured under license from Gemstar Development Corporation. SAFETY WARNINGS Observe all warnings for your safety and to ensure trouble free use of your VCR. INFORMATION Additional information complements instructions. (i) VCR REMOTE CONTROL 14. TIMER ON/OFF 5. AUDIO OUT (This button has no function with this model. ) TIMER ON/OFF MENU OPERATE INPUT SELECT AUDIO OUT CH VOL + 15. TV VOLUME + CH SKIP SEARCH VOL ZERO BACK SET / 17. PLUSCODE PLUSCODE CLEAR MODE OSD 1 4 7 AM/PM 2 5 8 0 3 DISPLAY 6 9 INPUT SELECT CHANNEL / 8. [. . . ] Press [ / ] to highlight the setting to be changed and correct it by using the [ / or the NUMBER BUTTONS. confirm, then press MENU to exit. ] 4. When all corrections are complete press SET to CANCELLING A RECORDING 1. Follow steps 1 to 3 of CHECKING A RECORDING. 2. To cancel a delayed recording, press [ / ] to highlight the recording to be cancelled, then press CLEAR. 1/2 DA T E P R S T AR T S T OP 2 1 / 0 6 0 2 1 2 : 0 0 1 3 : 0 0 SP * --/-- --:--:-- ----/-- --:--:-- ----/-- --:--:-- --- 3. Press MENU to exit. NOTE: · If there are some programmes to be recorded, do not forget to press TIMER ON/OFF button to return the VCR to TIMER POWERSAVE/TIMER STANDBY mode. If problems persist contact the SHARP Helpline on tel: 0990-274277 16 ADVANCED OPERATION PLAYBACK OF A VIDEO TAPE CHECKING THE AMOUNT OF TAPE REMAINING When you load a video tape into the VCR it can calculate approximately the amount of video tape remaining in hours and minutes. This is useful in determining whether or not there is sufficient tape left to make a recording. When a video tape is playing, the amount of tape remaining is calculated for you automatically. To display the amount of video tape remaining: 1. Press DISPLAY on the remote control as many times as necessary until "R" appears on the VCR display. The tape will wind forward and then return to its original position. Press MENU to display the main menu on the screen. MODE MENU SCREEN CO L OUR B L U E MU T E REPEAT POWE R S A V E AU T O AU T O ON ON PAL OF F OF F OF F 2. Press the [ select MODE. / ] menu select buttons to 3. Press [ / ] menu select buttons to select BLUE MUTE. / ] to select OFF. ON/OFF MENU OUT SEARCH BACK SET 6. Press SET and then MENU to return to the normal screen. PLUSCODE CLEAR MODE OSD 1 2 3 DISPLAY Remote Control COLOUR If the VCR is playing poor quality recording, the picture may turn black and white. Selecting PAL may improve this (depending on the recording), although coloured speckles may appear on black and white recordings. 1. Press [ / / ] menu select buttons to select COLOUR. ] to select AUTO/PAL. 4. Press SET and then MENU to return to the normal screen. If problems persist contact the SHARP Helpline on tel: 0990-274277 20 ADVANCED OPERATION SEARCHING THE VIDEO TAPE SKIP SEARCHING THE VIDEO TAPE You can search the tape in 30 second time intervals. To do this follow the procedure below: 1. Press PLAY/X2 ( ) to start the video tape playing. Press SKIP SEARCH on the remote control. The number of times you press SKIP SEARCH 1 press = 2 presses = determines the forward search time. 3 presses = 4 presses = After searching, normal playback will resume automatically 30 seconds. [. . . ] The guarantee does not cover carriage costs, batteries or video tapes. In the unlikely event of this product requiring repair, please contact the supplier from whom it was purchased. Where this is not possible, please contact the SHARP Helpline on the telephone number given below. 6. This guarantee is offered as an additional benefit to your statutory rights and does not affect these rights in any way. 7. [. . . ]