User manual SHARP VC-8300

[. . . ] 5 Auto installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 BASIC OPERATION Important notes on your VCR and video tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 How to playback a video tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Pausing and slow motion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If in TIMER POWERSAVE/TIMER STANDBY mode, press TIMER ON/OFF to exit. 2. Press [ confirm · · All the delayed recordings in the VCR's memory will be shown. Press SET to SET : SE L ECT : ENT ER ME NU : E X I T You can check the settings and change or cancel them. CHANGING A RECORDING 1. Follow steps 1 to 4 of CHECKING A RECORDING. 1/2 DA T E 21 / 06 --/---/---/-P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-SP ---- 2. If you wish to change a delayed recording, press [ / ] to highlight the recording, then press SET. 3. Press [ / ] to highlight the setting to be changed and correct it by using the[ / or the NUMBER BUTTONS. When all corrections are complete press SET, CANCELLING A RECORDING 1. Follow steps 1 to 4 of CHECKING A RECORDING. 2. If you wish to cancel a delayed recording, press [ / ] to highlight the recording to be cancelled, then press CLEAR. 1/2 DA T E P R S T AR T S T OP 2 1 / 0 6 0 2 1 2 : 0 0 1 3 : 0 0 SP --/-- --:--:-- ---/-- --:--:-- ---/-- --:--:-- -- 3. Press MENU. NOTE: · If there are some programmes to be recorded, do not forget to press TIMER ON/OFF button to return the VCR to TIMER POWERSAVE/TIMER STAND-BY mode. GB-13 ADVANCED OPERATION AUDIO AND YOUR VCR HI-FI STEREO SOUND Stereo sound is possible from this VCR if you have a stereo TV connected to the VCR with a scart lead, or audio equipment connected with audio phono leads. The VCR is normally set so that stereo sound is possible. This is useful in determining whether or not there is sufficient tape left to make a recording. When a video tape is playing, the amount of tape remaining is calculated for you automatically. To display the amount of video tape remaining: 1. Press DISPLAY on the remote control as many times as necessary until "R" appears on the VCR display. The tape will wind forward and then return to its original position. The tape remaining will be shown on the VCR display in hours and minutes. For example, if 1 hour 23 minutes is left on the tape: Pr NOTES: · · Do not interrupt the tape remaining calculation. If less than 5 minutes of tape remains the display will flash. PLAYING BACK A VIDEO TAPE REPEATEDLY You can set your VCR to automatically rewind at the end of playing a video tape and replay the entire tape again. REPEAT will appear on the on-screen display when selected. Press MENU to display the main menu on the screen. MODE MENU SCREEN B L U E MU T E R E P E A T AU T O ON OF F OF F 2. 7. Press [ / ] to select MODE. Press SET. [. . . ] · Safety device operating: unplug VCR for 2 hours. · Make sure the TV is set to the video channel. Playback picture is · Adjust the tracking using CHANNEL snowy. · The video heads may have been contaminated - refer to a SHARP Service Facility. [. . . ]