User manual SHARP VC-D806S

[. . . ] Please refer to the relevant laws in your country. G No part of this publication may be reproduced, stored or transmitted in any form without prior permission from SHARP Electronics (UK) Ltd. DELUXE G ® and PlusCode® are registered trademarks of Gemstar Development Corporation. G G G DELUXE system is manufactured under license from Gemstar Development Corporation. NEXTVIEWTM Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic", and the double-D symbol are trademarks of Dolby Laboratories. THIS MANUAL COVERS A RANGE OF MODELS. ALL OF THE FEATURES MENTIONED MAY NOT NECESSARILY APPLY TO YOUR VCR. SAFETY WARNINGS Observe all warnings for your safety and to ensure trouble free use of your VCR. INFORMATION Additional information complements instructions. (i) REMOTE CONTROL TV OPERATE CHANNEL TIMER ON/OFF 1. [. . . ] Follow steps 1 to 3 of CHECKING A RECORDING. 2. To cancel a delayed recording, press [ / ] to highlight the recording to be cancelled, then press CLEAR. 1/2 DA T E P R S T AR T S T OP 2 1 / 0 6 0 2 1 2 : 0 0 1 3 : 0 0 SP * --/-- --:--:-- ----/-- --:--:-- ----/-- --:--:-- --- 3. NOTE: · If there are some programmes to be recorded, do not forget to press TIMER ON/OFF button to return the VCR to TIMER POWERSAVE/TIMER STANDBY mode. If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours) or www. sharp. co. uk/support 19 ADVANCED OPERATION AUDIO AND YOUR VCR HI-FI STEREO SOUND Stereo sound is possible from this VCR if you have a stereo TV connected to the VCR with a scart lead, or audio equipment connected with audio phono leads. The VCR is normally set so that stereo sound is possible. The sound output from the VCR is controlled by the AUDIO OUT button on the remote control. If you wish to change the sound output you can use the AUDIO OUT button as follows: · · · · Press AUDIO OUT once. The LEFT audio channel will be sent to BOTH speakers. The RIGHT audio channel will be sent to BOTH speakers. The MONO track will be sent to BOTH speakers. L and R will disappear from the VCR display. Press PAUSE/STILL ( ) when you reach the point on the tape where you want audio dubbing to start. Press A. DUB (A. DUB will be shown on NOTE: The input source will be automatically changed to L3 (Front phono jacks) SP 7. Press PAUSE/STILL ( dubbing. ) , to start audio 8. Press STOP ( ) , to finish audio dubbing (A. DUB will disappear from your TV) If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours) or www. sharp. co. uk/support 22 ADVANCED OPERATION AUDIO DUBBING PLAYING BACK AN AUDIO DUBBED TAPE · If you want to listen to the original and the new dubbed audio signal simultaneously, you will need to set AUDIO MIX to ON. · You can change the audio output by pressing the AUDIO OUT button on the remote control. Refer to the table below. AUDIO MIX AUDIO OUT MODE VCR DISPLAY RESULT Original Hi-Fi audio (L&R channels) and dubbed audio ON Hi-Fi and Mono audio Original Hi-Fi audio (L channel) plus dubbed audio Original Hi-Fi audio (R channel) plus dubbed audio 1. Press MENU, to display the main menu on the screen. 2. Press [ / MODE MENU SCREEN to select MODE. / 3. ] to select ON. © AUDIO MIX 16: 9 POW ERS AVE LL 2/ 2 ON AUTO ON LL L L OF F OF F OF F 6. Press SET, to return to the menu screen. Press MENU, to exit to the normal screen. LM :SELECT :CHANGE SET :ENTER MENU :EXIT NOTES: . · Do not start audio dubbing until AUTO or MANUAL tracking has been completed as the audio signal will not be recorded correctly. · Because the audio signal is recorded onto the mono track any previous recording on this track will be erased. [. . . ] This will help minimise interference. If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours) or www. sharp. co. uk/support 52 GUARANTEE SHARP Electronics (UK) Ltd (hereafter called Sharp) guarantee to provide for the repair, or at its option the replacement, of this product subject to the conditions listed below: 1. This guarantee shall only apply to faults which are due to inferior workmanship or materials. It does not cover faults or damage by accident, misuse, fair wear and tear, neglect, tampering with the product, or repair other than by a Service Facility appointed by SHARP. 2. As this product is intended for private domestic use only, the guarantee will not apply if the product is used in the course of a business, trade or profession. 3. [. . . ]