User manual SHARP VCM20HM OPERATION MANUAL

[. . . ] Please refer to the relevant laws in your country. G No part of this publication may be reproduced, stored or transmitted in any form without prior permission from SHARP Electronics (Europe) GmbH. SAFETY WARNINGS Observe all warnings for your safety and to ensure trouble free use of your VCR. INFORMATION Additional information complements instructions. (i) VCR REMOTE CONTROL 14. TIMER ON/OFF 5. AUDIO OUT (This button has no function with this VCR) OPERATE INPUT SELECT TIMER ON/OFF MENU SV/V+ /TIMER AUDIO OUT CH VOL + 15. TV VOLUME + CH SKIP SEARCH VOL ZERO BACK SET / 17. SV/V+/TIMER CLEAR MODE OSD 1 4 7 AM/PM 2 5 8 0 3 DISPLAY 22. [. . . ] For example to record a programme on channel 3, press 0 3. Then press to move to the next setting. See next page to continue If problems persist contact the SHARP Helpline on tel: 0990-274277 13 BASIC OPERATION HOW TO SET A DELAYED RECORDING 7. Enter the start time using the [ / ] or the 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 -:---/-- --:--:---/-- --:--:-SP SP --- NUMBER BUTTONS, hours first then minutes (when entering less than 10 hours or minutes add a '0' before the number), for example for 21:05 start, press 2 1 0 5. Then press to move to the next setting. 8. Enter the stop time, for example for 22:30 stop, press 2 2 3 0. 9. If your VCR has long play facility and you wish to change the RECORDING SPEED, use the [ / ] to highlight SP. Press [ / ] to 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 2 2 : 3 0 --/-- --:--:---/-- --:--:-SP LP --- select standard play (SP) or long play (LP) as required. 10. Press the SET · SET button to confirm. The MENU now shows all the timer settings you have entered. If you wish to make additional timer recordings, repeat this procedure. 11. When you have completed entering timer settings, press the MENU button to remove the menu from the TV screen. 12. Ensure that the tape on which you wish to record is inserted into the VCR, then press the TIMER ON/OFF STANDBY mode. The tape will wind forward and then return to its original position. The tape remaining will be shown on the VCR display in hours and minutes. By pressing the TAPE SPEED button on the remote control the remaining time will change between long play and standard play. For example, in standard play 1 hour 23 minutes is left on the tape: Pr in long play 2 hour 46 minutes is left on the tape: Pr NOTES: · · If tape remaining function is interrupted, the remaining time will not be displayed. If less than 5 minutes of tape remains the display will flash. PLAYING BACK A VIDEO TAPE REPEATEDLY You can set your VCR to automatically rewind at the end of playing a video tape and replay the entire tape again. REPEAT will appear on the on-screen display when selected. Press the[ / SET button to display the main menu on the screen. ]menu select buttons to MODE MENU SCREEN B L U E MU T E R E P E A T AU T O ON OF F OF F select MODE. 3. ]to select REPEAT. : SE L ECT : ENT ER : CHANGE ME NU : E X I T / ]to select ON. SET SET 6. Press the MENU normal screen. button. button to return to If problems persist contact the SHARP Helpline on tel: 0990-274277 16 ADVANCED OPERATION DIGITAL DISPLAY TIME OF DAY Shows current time of day, if the clock is set. [. . . ] It does not cover faults or damage by accident, misuse, fair wear and tear, neglect, tampering with the product, or repair other than by a Service Facility appointed by SHARP. As this product is intended for private domestic use only, the guarantee will not apply if the product is used in the course of a business, trade or profession. To benefit from this guarantee, any fault which occurs must be notified to SHARP, or its appointed Service Facility within one year from the date this product was purchased. The guarantee does not cover carriage costs, batteries or video tapes. [. . . ]