User manual SHARP VCM25HM OPERATION MANUAL PAGE 15 TO END

[. . . ] Replace both alkaline batteries (type AA/R6/UM3) if the remote control fails. Remove the batteries and keep in a safe place if you do not plan to use the VCR for several months. Remove and dispose of flat batteries safely and promptly. [. . . ] connect the VCR RF OUT socket to the TV AERIAL IN socket. AERIAL RF CONNECTION CABLE Optional SCART (not supplied). If you have a scart lead connect it to your TV and LINE 1 IN/OUT socket on the VCR. - The advantage of a Scart connection is improved picture and sound quality during playback. BACK OF TELEVISION 3 Connect the VCR to the mains. AERIAL RF CONNECTION CABLE SCART LEAD The VCR is correctly connected. If problems persist contact the SHARP Helpline on tel: 0990-274277 4 INSTALLING YOUR VCR TUNING THE TV INTO THE VCR 1. Press the STANDBY button to ensure your VCR is in the STANDBY mode. The display on the front of the VCR should show "SHARP", if not, please perform the VCR RESET procedure on page 30. button located on VCR front panel for 3 seconds. The VCR will search and display an ideal EXAMPLE channel. Wait for the flashing channel number to appear on the VCR display, this number will be between 21 and 69. 2. Press and hold the CAUTION: If the clear button is pressed at this point it will not allow the TV to be tuned to the VCR. Refer to RF through ON/OFF on page 30. 3. Press [ / / / ] to highlight 3. 1 CH 2 1 2 CH 3 2 3 CH 4 3 4 CH 5 4 5 CH 6 5 6 SE L ECT ED SET MOV E 1/3 7 13 8 14 9 15 10 16 11 17 12 18 : CH 6 5 : SE L ECT ED : ENT ER ME NU : E X I T the channel to be moved. 4. Press the SET button to confirm. 5. Press [ / / / ] to highlight 5. 1 CH 6 5 2 CH 2 1 3 CH 3 2 4 CH 4 3 5 CH 5 4 6 SE L ECT ED SET MOV E 1/3 7 13 8 14 9 15 10 16 11 17 12 18 : CH 6 5 : SE L ECT ED : ENT ER ME NU : E X I T the new position for the channel. 6. Press the SET button to confirm. 7. If any more channels are to be moved, repeat procedure from step 3. 8. Press the button to exit if you are happy with the channel order. REMOTE CONTROL MENU SET If you wish to change the channel order at a later date refer to MANUALLY SORTING CHANNELS - Sorting the channels into your preferred order. MENU SELECT BUTTONS If problems persist contact the SHARP Helpline on tel: 0990-274277 7 INSTALLING YOUR VCR INSTALLATION CONTINUED . MENU SV/V+/ TIMER SET CLEAR MODE OSD 1 4 2 5 8 0 3 DISPLAY 6 9 INPUT SELECT The clock setting screen will now appear. To set the time and date follow the steps below: 7 AM/PM CHANNEL Remote Control 1. Press the [ / ] menu select buttons to select either 12 or 24 hour clock operation. 2. Enter / ] 24 hour example: C L OCK MOD E 2 4H T I ME 15 : 05 DA T E 01 / 04 Y E AR 00 the time using the NUMBER BUTTONS or the [ buttons. [. . . ] Enter / ] 24 hour example: C L OCK MOD E 2 4H T I ME 15 : 05 DA T E 01 / 04 Y E AR 00 the time using the NUMBER BUTTONS or the [ buttons. If the minutes or hours are less than 10, enter the leading 0. If using the 12 hour clock enter AM or AM/PM PM by pressing the AM/PM button on the remote control. MOD E : 2 4 H / 1 2 H : SE L ECT : CHANGE SE T : ENT ER ME NU : E X I T 3. [. . . ]