User manual SHARP VCM271HM OPERATION MANUAL ERRATA SHEET

[. . . ] Please refer to the relevant laws in your country. G No part of this publication may be reproduced, stored or transmitted in any form without prior permission from SHARP Electronics (UK) Ltd. ® and PlusCode® are registered trademarks of Gemstar Development G Corporation. G system is manufactured under license from Gemstar Development Corporation. This manual covers a range of models, not all of the features included will be relevant to your VCR. If you require any advice or assistance regarding your Sharp product, please visit our web-site www. sharp. co. uk/support. Customers without Internet access may telephone 08705 274277 during office hours (or (01)676 0648 if telephoning from Ireland). SAFETY WARNINGS Observe all warnings for your safety and to ensure trouble free use of your VCR. INFORMATION Additional information complements instructions. (i) TINS-3991UMZZ HM Final Cover 8/6/01 10:44 am Page 3 VCR REMOTE CONTROL 14. AUDIO OUT (This button has no function with this model) 15. STOP (The STOP button is also used to switch on the VCR. ) 11. [. . . ] Press the SET button again, the on-screen display will now show today's date. If you wish to change the date use the [ / ]or NUMBER BUTTONS. If you use the number buttons, enter two digits for the day, then two for the month. For example for July 9th, press 0 9 (9th), then 0 7 (July). When the correct date for your recording is shown, press the menu select button to move to the next setting. SET DISPLAY REMOTE CONTROL 3. MENU SCREEN ME NU V I D EOP L U S + T I ME R MOD E SE T UP 4. 1/2 DA T E 21 / 06 9 / 07 --/---/-P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-SP ---- 5. If you want to make additional recordings at the same time each day or week, use the [ / ] buttons to select D (daily) or W (weekly). Then press to move to the next setting. 5. 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D - -:--:---/-- --:--:---/-- --:--:-SP ---- 6. Enter the channel number using the [ / ]or the NUMBER BUTTONS. For example to record a programme on channel 3, press 0 3. Then press to move to the next setting. See next page to continue www. sharp. co. uk/support 15 TINS-3991UMZZ. book Page 16 Friday, June 8, 2001 11:44 AM BASIC OPERATION HOW TO SET A DELAYED RECORDING 7. Enter the start time using the[ / ] or 7. 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 -:---/-- --:--:---/-- --:--:-SP SP --- NUMBER BUTTONS, hours first then minutes (when entering less than 10 hours or minutes add a '0' before the number), for example for 21:05 start, press 2 1 0 5. This is useful in determining whether or not there is sufficient tape left to make a recording. When a video tape is playing, the amount of tape remaining is calculated for you automatically. To display the amount of video tape remaining: 1. Press DISPLAY on the remote control as many times as necessary until "R" appears on the VCR display. The tape will wind forward for a few seconds and then return to its original position. The tape remaining will be shown on the VCR display in hours and minutes. By pressing the TAPE SPEED button on the remote control the remaining time will change between standard play and long play. For example, in standard play 1 hour 23 minutes is left on the tape: in long play 2 hours 46 minutes is left on the tape: NOTES: · · If tape remaining function is interrupted, the remaining time will not be displayed. If less than 5 minutes of tape remains the display will flash. PLAYING BACK A VIDEO TAPE REPEATEDLY You can set your VCR to automatically rewind at the end of playing a video tape and replay the entire tape again. REPEAT will appear on the on-screen display when selected. Press the[ / SET button to display the main menu on the screen. [. . . ] (White text blue background) V CR R F SET : ENT ER ME NU : E X I T RF THROUGH ON/OFF: If you wish to connect your VCR to the TV with only a scart lead, the RF Output on your VCR can be turned OFF and ON. To do this press the CLEAR then SET SET buttons on the remote control at point 3 from RF CHANNEL TUNING above. or at point 4 of AUTO TUNING on page 5. This will help minimise interference. www. sharp. co. uk/support 33 TINS-3991UMZZ. book Page 34 Friday, June 8, 2001 11:44 AM GUARANTEE SHARP Electronics (UK) Ltd. [. . . ]