User manual SHARP VCM315HM OPERATION MANUAL, CONTENTS & MAIN BODY.

[. . . ] TINS-A078UMN1. book Page 1 Monday, November 4, 2002 1:21 PM CONTENTS BEFORE USING YOUR VCR Important notes on your VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Unpacking the accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLING YOUR VCR Connecting the cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Auto Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] appears on the VCR display, button to remove the CHECKING A RECORDING 1. Press the SET · SET MENU SCREEN T I ME R MOD E SE T UP button to confirm. All the delayed recordings in the VCR's memory will be shown. button to exit. : SE L ECT : ENT ER 4. If the settings are correct press the MENU SET ME NU : E X I T · If you wish to change or cancel any settings, follow the procedures below. CHANGING A RECORDING 1. Follow steps 1 to 3 of CHECKING A RECORDING above. 2. To change a delayed recording, press [ / ] to highlight the recording, then press SET the SET button to select. 3. Press[ / ]to highlight the setting to be / ] 1/2 DA T E 21 / 06 --/---/---/-P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-SP ---- changed and correct it by using the[ or the NUMBER BUTTONS. SET 4. When all corrections are complete press the SET button to confirm, then press the MENU button to exit. Follow steps 1 to 3 of CHECKING A RECORDING above. 2. To cancel a delayed recording, press [ / ]to highlight the recording to be button to exit. cancelled, then press CLEAR. 1/2 DA T E P R S T AR T S T OP 2 1 / 0 6 0 2 1 2 : 0 0 1 3 : 0 0 SP --/-- --:--:-- ---/-- --:--:-- ---/-- --:--:-- -- 3. Press the MENU NOTE: · If there are some programmes to be recorded, do not forget to press TIMER ON/OFF button to return the VCR to Timer Standby mode. www. sharp. co. uk/support 17 TINS-A078UMN1. book Page 18 Monday, November 4, 2002 1:21 PM ADVANCED OPERATION PLAYBACK OF A VIDEO TAPE CHECKING THE AMOUNT OF TAPE REMAINING When you load a video tape into the VCR it can calculate approximately the amount of video tape remaining in hours and minutes. This is useful in determining whether or not there is sufficient tape left to make a recording. When a video tape is playing, the amount of tape remaining is calculated for you automatically. To display the amount of video tape remaining: 1. Press DISPLAY on the remote control as many times as necessary until "R" appears on the VCR display. The tape will wind forward and then return to its original position. The tape remaining will be shown on the VCR display in hours and minutes. By pressing the TAPE SPEED button on the remote control the remaining time will change between long play and standard play. For example, in standard play 1 hour 23 minutes is left on the tape: in long play 2 hours 46 minutes is left on the tape: NOTES: · · If tape remaining function is interrupted, the remaining time will not be displayed. If less than 5 minutes of tape remains the display will flash. PLAYING BACK A VIDEO TAPE REPEATEDLY You can set your VCR to automatically rewind at the end of playing a video tape and replay the entire tape again. [. . . ] (hereafter called Sharp) guarantee to provide for the repair, or at its option the replacement, of this product subject to the conditions listed below: 1. This guarantee shall only apply to faults which are due to inferior workmanship or materials. It does not cover faults or damage by accident, misuse, fair wear and tear, neglect, tampering with the product, or repair other than by a Service Facility appointed by SHARP. As this product is intended for private domestic use only, the guarantee will not apply if the product is used in the course of a business, trade or profession. [. . . ]