User manual SHARP VCMH60HM OPERATION MANUAL

[. . . ] Please refer to the relevant laws in your country. No part of this publication may be reproduced, stored or transmitted in any form without prior permission from SHARP Electronics (Europe) GmbH. and PlusCode are trademarks of Gemstar Development Corporation. system is manufactured under license from Gemstar Development Corporation. q q q q THIS MANUAL COVERS A RANGE OF MODELS. [. . . ] Press [ ] to select standard play or long play as required. q The MENU now shows all the timer settings you have entered. If you wish to make additional timer recordings, repeat this procedure. 12. When you have completed entering timer settings, press MENU to remove the menu from the TV screen. 13. Press TIMER ON/OFF once to place the VCR in TIMER STAND-BY mode. will be shown on the display. 1/2 P R S T AR T S T OP DA T E 21 / 06 02 12 : 00 1 3 : 00 S P 9 / 0 7 D0 3 2 1 : 0 5 - : - - SP -:-- -/- - - -:----:-- -/- - - -:---- 1/2 P R S T AR T S T OP DA T E 21 / 06 02 12 : 00 1 3 : 00 S P 9 / 0 7 D0 3 2 1 : 0 5 2 2 : 3 0 L P -:--:---- -/- - - -:--:---- -/- - - - 1/2 P R S T AR T S T OP DA T E 21 / 06 02 12 : 00 1 3 : 00 S P 9 / 0 7 D0 3 2 1 : 0 5 2 2 : 3 0 L P -:--:---- -/- - - -:--:---- -/- - - - NOTES: q If q If flashes a video tape has not been inserted into the VCR. the video tape is ejected when the VCR tries to record the record protection tab has been removed. q During recording, press STOP ( ) to cancel the recording. If there are further recordings to be made, the VCR will return to TIMER STANDBY. 14 BASIC OPERATION HOW TO SET A DELAYED RECORDING CHECKING, CHANGING AND CANCELLING A RECORDING CHECKING A RECORDING 1. If in TIMER STANDBY mode, press TIMER ON/OFF to exit. q All the delayed recordings in the VCRs memory will be shown. q If the poor quality is for a long period the VCR will automatically select the mono track and the sound will be in mono. 16 ADVANCED OPERATION AUDIO AND YOUR VCR CONNECTING TO AUDIO EQUIPMENT The diagram below shows how to connect your VCR to audio equipment. When connected in this way stereo sound is possible from the speakers. BACK OF TELEVISION EXISTING AERIAL CABLE RF CONNECTION CABLE RF OUT ANTENNA IN ENTREE ANTENNE RF OUT SORTIE ANTENNE AERIAL IN AUDIO OUT L and R AUDIO PHONO LEADS + AMPLIFIER 17 ADVANCED OPERATION PLAYBACK OF A VIDEO TAPE CHECKING THE AMOUNT OF TAPE REMAINING When you load a video tape into the VCR it can calculate approximately the amount of video tape remaining in hours and minutes. This is useful in determining whether or not there is sufficient tape left to make a recording. When a video tape is playing, the amount of tape remaining is calculated for you automatically. To display the amount of video tape remaining: 1. Press DISPLAY on the remote control as many times as necessary until "R" appears on the VCR display. The tape will wind forward and then return to its original position. The tape remaining will be shown on the VCR display in hours and minutes. For example, if 1 hour 23 minutes is left on the tape: Pr NOTES q q Do not interrupt the tape remaining calculation. If less than 5 minutes of tape remains the display will flash. PLAYING BACK A VIDEO TAPE REPEATEDLY You can set your VCR to automatically rewind at the end of playing a video tape and replay the entire tape again. [. . . ] Playback picture is snowy. q q q The channel position has been set to be skipped. Make sure all the cables are connected properly. Make sure VCR power cord is properly plugged in. q q q q q / Adjust the tracking using CHANNEL buttons. The video heads may have been contaminated - refer to a SHARP Service Facility. The record-protection tab has been removed. Tape is automatically ejected when pressing REC ( ) or TIMER ON/OFF buttons. [. . . ]