User manual SHARP VCMH703 OPERATION MANUAL

[. . . ] Please refer to the relevant laws in your country. G No part of this publication may be reproduced, stored or transmitted in any form without prior permission from SHARP Electronics (Europe) GmbH. ® and PlusCode ® are registered trademarks of Gemstar Development G Corporation. G system is manufactured under license from Gemstar Development Corporation. SAFETY WARNINGS Observe all warnings for your safety and to ensure trouble free use of your VCR. INFORMATION Additional information complements instructions. (i) VCR REMOTE CONTROL 14. PLUSCODE TIMER ON/OFF MENU OPERATE INPUT SELECT AUDIO OUT CH VOL + 15. TV VOLUME + CH SKIP SEARCH VOL ZERO BACK SET / 17. CLEAR PLUSCODE CLEAR MODE OSD 1 4 7 AM/PM 2 5 8 0 3 DISPLAY 22. [. . . ] Enter the start time using the [ / ] or the 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 -:---/-- --:--:---/-- --:--:-SP SP --- NUMBER BUTTONS, hours first then minutes (when entering less than 10 hours or minutes add a '0' before the number), for example for 21:05 start, press 2 1 0 5. Then press to move to the next setting. 8. Enter the stop time, for example for 22:30 stop, press 2 2 3 0. 9. If your VCR has long play facility and you wish to change the RECORDING SPEED, use the [ / ] to highlight SP. Press [ / ] to 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 2 2 : 3 0 --/-- --:--:---/-- --:--:-SP LP --- select standard play (SP) or long play (LP) as required. 10. Press the SET · SET button to confirm. The MENU now shows all the timer settings you have entered. If you wish to make additional timer recordings, repeat this procedure. 11. When you have completed entering timer settings, press the MENU button to remove the menu from the TV screen. 12. Ensure that the tape on which you wish to record is inserted into the VCR, then press the TIMER ON/OFF TIMER ON/OFF button once to will place the VCR in TIMER STANDBY mode. be shown on the display. NOTES: · · · If flashes a video tape has not been inserted into the VCR. If the video tape is ejected when the VCR tries to record the record protection tab has been removed. Pressing the AUDIO OUT button a fourth time, normal Hi-Fi stereo sound will be heard. L and R will appear on the VCR display. AUDIO OUT AUDIO OUT AUDIO OUT AUDIO OUT · · · NICAM Hi-Fi STEREO SOUND Your VCR can receive and record NICAM sound. The VCR is normally set so that NICAM sound is possible if it is present on the receiving signal, otherwise the VCR will automatically switch to receive the mono signal. If you wish to do this follow the procedure below: 1. / button to display the main menu on the screen. ] menu select buttons to SET N I CAM CO L OUR AU T O AU T O OF F PAL 3. Press [ / ] to select OFF. SET 5. Press the SET NOTES: · button, to return to the menu screen. Press the MENU If the tape being played back does not carry sound recorded on Hi-Fi tracks, L and R will not appear on the display. · lf the sound contains `crackling' or `popping' noises the sound quality may be improved by adjusting the tracking using the CHANNEL CHANNEL CHANNEL / buttons. · If the poor quality is for a long period the VCR will automatically select the mono track and the sound will be in mono. · NICAM sound may not be stereo. If problems persist contact the SHARP Helpline on tel: 0990-274277 18 ADVANCED OPERATION AUDIO AND YOUR VCR CONNECTING TO AUDIO EQUIPMENT The diagram below shows how to connect your VCR to audio equipment. When connected in this way stereo sound is possible from the speakers. EXISTING AERIAL CABLE BACK OF TELEVISION RF CONNECTION CABLE ANTENNA IN ENTREE RF OUT SORTIE ANTENNE AERIAL IN RF-OUT AUDIO OUT L and R AUDIO PHONO LEADS (NOT SUPPLIED) + AMPLIFIER If problems persist contact the SHARP Helpline on tel: 0990-274277 19 ADVANCED OPERATION PLAYBACK OF A VIDEO TAPE CHECKING THE AMOUNT OF TAPE REMAINING When you load a video tape into the VCR it can calculate approximately the amount of video tape remaining in hours and minutes. [. . . ] It does not cover faults or damage by accident, misuse, fair wear and tear, neglect, tampering with the product, or repair other than by a Service Facility appointed by SHARP. As this product is intended for private domestic use only, the guarantee will not apply if the product is used in the course of a business, trade or profession. To benefit from this guarantee, any fault which occurs must be notified to SHARP, or its appointed Service Facility within one year from the date this product was purchased. The guarantee does not cover carriage costs, batteries or video tapes. [. . . ]