User manual SHARP VELC2H OPERATION MANUAL

[. . . ] Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. [. . . ] · Allow a margin of error in the value. XG-SV200X Position of the image when the image is centered, both vertically and horizontally, in lens shift VELC2H Position of the image when the image is centered, both vertically and horizontally, in lens shift 0. 5V 0. 5V 1V 1V 0. 5V 0. 5V 0. 23H 1H 0. 23H 0. 25H 1H 0. 25H V : Height of the image H : Width of the image V : Height of the image H : Width of the image 28 1 Press H&V SHIFT on the remote control. · Pressing ENTER on the projector or on the remote control displays the test pattern. Checking the test pattern is useful for more accurate adjustment. ROn-screen display ENTER button Adjustment buttons (P/R/O/Q) RETURN button LENS SHIFT END LENS SHIFT TESTPATTERN LENS CENTER 2 Press P, R, O or Q on the projector or the remote control to adjust the image position. Note H&V SHIFT button · When RETURN is pressed, the lens shift reset screen is displayed. Lens shift can be reset to factory default with this screen. Using the Adjustment Feet Basic Operation · When the position of the projected image cannot be adjusted with the lens shift function, use the adjustment feet to adjust the projected angle. · The height of the projector can be adjusted using the adjustment feet when the screen is located higher than the projector, the screen is inclined or when the installation site is slightly inclined. · Install the projector so that it is as perpendicular to the screen as possible. 1 Rotate the adjustment feet to adjust the projected angle. · The projector is adjustable up to approximately 9 degrees (front) and approximately ±2 degrees (rear) from the standard position. Adjustment feet Warning! · Do not hold the lens and lens cover when projector angle is adjusted. · Use caution not to pinch your finger in the space between the adjustment foot and the projector when the projector angle is lowered. Down Up Up Down 29 Image Projection (Continued) Adjusting the Focus Press FOCUS +/­ on the remote control to adjust the focus. ROn-screen display FOCUS TESTPATTERN Info · It is recommended that the focus be adjusted after the projector has warmed up for at least 30 minutes. ZOOM buttons FOCUS buttons Adjusting the Projected Image Size Press ZOOM +/­ on the remote control to adjust the projected image size. ROn-screen display ZOOM TESTPATTERN Note · After you have pressed FOCUS or ZOOM on the remote control, you can display the test pattern by pressing ENTER. The test pattern is useful for making more accurate adjustments. · For fine adjustments, when H&V SHIFT, FOCUS or ZOOM is pressed, the projected image moves a small amount in the desired direction for approximately one second. Hold down the buttons to move the projected image quickly. 30 Correcting Trapezoidal Distortion When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. Please use caution. About Copyrights 39 Operating with the Remote Control AUTO SYNC button FREEZE button POINTER button SPOT button Adjustment buttons (P/R/O/Q) RETURN button EFFECT button MAGNIFY buttons PICTURE MODE button ECO+QUIET button BREAK TIMER button Displaying the Pointer 1 Press POINTER and press P/R/ O/Q on the remote control to move the pointer. Star Finger1 Finger2 Heart · Press EFFECT to change the pointer icon (5 types). Underline 2 Press POINTER again. · The pointer will disappear. Displaying and Setting the Break Timer Using the Spot Function 1 Press BREAK TIMER. On-screen display 1 · The timer starts to count down from 5 minutes. Press SPOT and press P/R/O/Q on the remote control to move the spot area. · Press EFFECT to change the spot area size (3 types). 1/9 1/25 1/8 2 Press P/R/O/Q to adjust the length of the break time. · Increases with P or Q · Shortens with O or R 5 minutes 6 minutes 60 minutes 2 Press SPOT again. · The spot area will disappear. 4 minutes 3 minutes 1 minute · The break time can be set in units of one minute (up to 60 minutes). Canceling the break timer display function Switching the Eco+Quiet Mode Press ECO+QUIET to switch the Eco+Quiet mode between on and off. Press BREAK TIMER. Note · The Break Timer is not available while the projector is operating the following functions. - Auto Sync - Freeze - AV Mute · When the Eco+Quiet is set to "ON", the sound of the cooling fan will turn down, the power consumption will decrease, and the lamp life will extend. Note · Refer to "Eco+Quiet" on page 50 for details. 40 Auto Sync (Auto Sync Adjustment) Auto Sync function works when detecting input signal after the projector turns on. Press AUTO SYNC to manually adjust with Auto Sync function. Note · When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page 52. ) Displaying an Enlarged Portion of an Image Graphs, tables and other portions of projected images can be enlarged. This is helpful when providing more detailed explanations. 1 Press MAGNIFY on the remote control. · Enlarges the image. · Pressing or MAGNIFY enlarges or reduces the projected image. Note Press . Freezing a Moving Image ×1 ×2 ×3 ×4 ×9 Press . 1 2 Press FREEZE. · The projected image is frozen. · You can change the location of the enlarged image using P, R, O and Q. Press FREEZE again to return to the moving image from the currently connected device. 2 Press RETURN on the remote control to cancel the operation. · The magnification then returns to 1. Note Selecting the Picture Mode You can select the appropriate Picture mode for the projected image, such as movie or video game. · When pressing PICTURE MODE, the Picture mode changes in the following order: STANDARD PRESENTATION MOVIE GAME sRGB* Press PICTURE MODE. Note · See page 48 for details on the Picture mode. * "sRGB" is displayed only when RGB signal is input. · The selectable magnifications differ depending on the input signal. · This function is not available for the 3D mode. · In the following cases, the image will return to the normal size ( 1). - When the input signal resolution and refresh rate (vertical frequency) change. - When switching "DLP® LinkTM" between "On" and "Off". 41 Useful Features Operating with the Remote Control (Continued) Using the Remote Control as the Wireless Computer Mouse When connecting the projector and the computer with a USB cable, you can use the remote control as the computer mouse. Connecting with a USB cable Computer To USB terminal To USB terminal USB cable (commercially available or available as Sharp service part QCNWGA014WJPZ) The mouse pointer can be operated in the following way after it is connected. When moving the cursor When left-clicking Press L-CLICK. [. . . ] Any obstructions may cause the glasses not to function properly causing the lenses to flicker or turn off. Do not place your hand or other objects in front of the 3D control signal sensor on the glasses. · Check whether there is a source of high intensity lighting nearby. High intensity lighting can interfere with communication between the 3D LCD shutter glasses and the screen resulting in some flicker. [. . . ]