User manual SHARP VL-AX1 OPERATION MANUAL PART 1

[. . . ] SVENSKA VIDEOKAMERA MED FLYTANDE KRISTALLSKRM CAMCORDER COM VISOR DE CRISTAL LQUIDO LIQUID CRYSTAL DISPLAY CAMCORDER VL-AX1S PORTUGUS BRUKSANVISNING MANUAL DE OPERAO ;;; ;; ;; ;;; BRUKSANVISNING MANUAL DE OPERAO OPERATION MANUAL ENGLISH OPERATION MANUAL VL-AX1S-CE1; 01/10/1/18:00 This equipment complies with the requirements of Directives 89/336/ EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gert entspricht den Anforderungen der EG-Richtlinien 89/336/ EWG und 73/23/EWG mit nderung 93/68/EWG. Ce matriel rpond aux exigences contenues dans les directives 89/336/ CEE et 73/23/CEE modifies par la directive 93/68/CEE. Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/ 23/EEG, gewijzigd door 93/68/EEG. [. . . ] Press and hold the power source UNLOCK release in the direction of the arrow (1), then slide the battery pack up and tail it out (2). Power source UNLOCK release 1 Make sure that the POWER switch is set to OFF. Preparation POWER switch 2 Pull out the viewfinder completely (1), then lift it up (2). 60 3 Align the = mark on the side of the battery pack with the = mark on the camcorder (1). Press the battery pack and slide it down completely until it locks into place (2). Cautions: BEFORE REMOVING THE BATTERY PACK, ALWAYS STOP RECORDING OR PLAYBACK AND TURN THE POWER OFF. Removing the battery pack while shooting or during playback may damage the tape by causing it to wrap around the video head drum or destroy the card, rendering it unreadable and unwritable. Remove the battery pack from the camcorder if you will not use the camcorder for a long period of time. Make sure that the battery pack is firmly attached during operation. If it is not, the battery pack may come off or camcorder operation may fall because of the poor contact pressure. To prevent damage to the battery pack when removing, be sure to firmly hold the battery pack while pressing the release. Use only SHARP model BT-L221, BT-L441, BTLS222 or BT-LS442A battery packs with this camcorder. Use of other batteries may create a risk of fire or explosion. 4 Lower the viewfinder (1), and push it in completely (2). 10 VL-AX1S-GB-009-021 10 01. 10. 9, 1:24 PM Preparation Powering the Camcorder from an AC Outlet Preparation You can also power the camcorder from a power outlet by using the supplied AC adapter/ battery charger and DC cable. Caution: The supplied AC adapter/battery charger is specially designed for use with this camcorder, and should not be used as a power supply for other camcorders. DC OUT jack POWER indicator To power outlet Note: When using the AC adapter/battery charger to power the camcorder, it cannot be used to charge the battery pack. 1 2 3 Make sure that the POWER switch is set to OFF. Pull out the viewfinder completely, then lift it up. Align the = mark on the side of the DC cable connecting plate with the = mark on the camcorder (1). Press the connecting plate and slide it down completely until it locks into place (2). Removing the DC cable from the camcorder Perform steps 1 and 2 above. Press and hold the power source UNLOCK release in the direction of the arrow (1), then slide the connecting plate up and tail it out (2). Power source UNLOCK release DC cable connecting plate 4 5 Lower the viewfinder, and push it in completely Insert the DC cable plug into the DC OUT jack on the AC adapter. Connect the supplied power cord to the AC adapter, and insert the AC plug into a power outlet. The POWER indicator on the AC adapter lights up, and the camcorder is supplied power. Cautions: BEFORE REMOVING THE DC CABLE, ALWAYS STOP RECORDING OR PLAYBACK AND TURN THE POWER OFF. Removing the DC cable while shooting or during playback may damage the tape by causing it to wrap around the video head drum or destroy the card, rendering it unreadable and unwritable. Disconnect the camcorder from the AC adapter if you will not use the camcorder for a long period of time. The supplied DC cable is designed for use only with the supplied AC adapter/battery charger. Do not use it with the other equipment, as this may damage the cable or the equipment. 11 VL-AX1S-GB-009-021 11 01. 10. 9, 1:24 PM Inserting and Removing a Cassette Inserting 5 Wait for the cassette holder to fully retract. Close the compartment door by pressing the centre until it clicks into place. 1 2 Attach the power source to the camcorder. Hold the camcorder as shown below, slide the cassette compartment door release and open the cassette compartment door completely. After confirmation sound, the cassette holder extends and opens automatically. Cassette compartment door release Preparation Removing Perform steps 1 and 2 above, then take out the cassette. Cautions: Do not try to close the cassette compartment door while the cassette holder is extending or retracting. Be careful not to get your fingers caught in the cassette holder. Do not apply force to the cassette holder except when pressing the W mark to close it. [. . . ] E F F E C T B W 5 Press the MENU button to turn off the menu screen. To cancel the digital picture effect Select "OFF" in step 4 above. Notes: Digital picture effects cannot be used when a still image is displayed. Digital picture effects can be used in TAPE-VCR and CARD-VCR mode. 1 Useful Features In TAPE-CAMERA mode, press the MENU button until the menu screen appears. Turn the CONTROL dial to select T, then press the dial. Turn the CONTROL dial to select "PIC. [. . . ]