User manual SHARP VL-E630H OPERATION MANUAL

[. . . ] Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/EEG. Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. Quest' apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/ EEC, come emendata dalla direttiva 93/68/EEC. [. . . ] Press l or m to select "TAPE SPEED", then press the centre of the Operation button. S E T T I NG 1 QK . R E T URN W I D E MOD E D G T L Z O OM TAPE SPEE D SP LP RE T URN 2 3 Useful Features 4 Press l or m to select "LP", then press the centre of the Operation button. T AP E SP E ED LP 5 Press the MENU button to turn off the menu screen. · The long play recording mode indicator only appears when the onscreen indicators are turned on. LP PAUSE TAP Long play recording mode indicator 40 Selecting the 16-bit Audio Recording Mode The camcorder normally records audio in the 12-bit audio recording mode. For higherquality audio recording, select the 16-bit audio recording mode. 4 Press l or m to select "16bit", then press the centre of the Operation button. AUD I O MODE 1 6 bit 5 Press the MENU button to turn off the menu screen. · The 16-bit audio recording mode indicator only appears when the onscreen indicators are turned on. PAUSE TAP 1 6 bit 1 2 3 In Camera mode, press the MENU button to display the menu screen. Press l or m on the Operation button to select Y, then press the centre of the Operation button. Press l or m to select "AUDIO MODE", then press the centre of the Operation button. S E T T I NG 2 DIS A U D I O MO D E 1 2 bit 1 6 bit W I ND R E T URN 16-bit audio recording mode indicator To return to 12-bit audio recording mode Select "12bit" in step 4 above. Useful Features Note: · When using Audio Dubbing with 16-bit audio recordings, both the dubbed and original sounds will be recorded in mono (see page 58). 41 Useful Features Useful Features Playback Playback Using the Remote Control (Not Supplied) The remote control (RRMCGA237WJSA) is not supplied with this camcorder. Contact the nearest SHARP service centre or your dealer for purchasing as specified part. Operating Aim the remote control at the remote sensor of the camcorder, and press the control buttons to operate. Activating 5 · The example screens shown are for Playback mode. m Remote sensor 1 2 3 Useful Features Press the MENU button to display the menu screen. Press l or m on the Operation button to select Z, then press the centre of the Operation button. ZOOM (W/T) buttons Press l or m to select "REMOTE", then press the centre of the Operation button. OTHE RS 1 DE F AUL T ON R EMO T E BEEP OF F *S - V I D E O I N R E T U RN TAPE REC START/STOP button * CARD REC button * CARD PLAY/MULTI button SLOW button FF button PLAY/STILL button * "S-VIDEO IN" does not appear with VL-Z100. Advance/reverse buttons * Shift buttons VOLUME +/L buttons T/C (Time Code) button DATE button STOP button REW button Notes: · Be careful not to expose the remote sensor to direct sunlight or strong interior lighting, as this may prevent the remote control from operating properly. · Be sure that there are no obstacles between the remote control and the remote sensor. · The buttons with an asterisk mark (*) do not work with this camcorder. 4 Press l or m to select "ON", then press the centre of the Operation button. REMOT E ON 5 Press the MENU button to turn off the menu screen. 42 Selecting the Date and Time of Recording Display Follow the procedure below to select the date, or both the date and time, of recording display on the screen. You can display the date and time during both recording and playback. · The example screens shown are for Playback mode. 5 Press the MENU button until the date (or date and time) appears. 2. 200 5 FF 1 2 3 Press the MENU button to display the menu screen. A 16:9 image is compressed and recorded (squeeze recorded) as a 4:3 image. · In stretch playback mode, you cannot perform picture effect playback. · When outputting the stretch playback image from the DV terminal, the original image signal will be output. · When performing stretch playback, the normal recorded image (picture aspect ratio 4:3) will be stretched as shown below. 4:3 picture aspect ratio image Stretch playback 1 2 Useful Features In Playback mode, press the DISPLAY/MODE SET button until the mode screen appears. Press l or m on the Operation button to select "STRETCH PB", then press the centre of the Operation button. P I C. EF F ECT A U D I O DU B STRETCH PB EXE CUT E · Playback will stop after turning on stretch playback. 3 Press m to begin stretch playback. AUDIO1 + 2 STRE T CH PB CANC E L PAUSE STOP R EW FF · The picture displays with black bands. 46 Advanced Features Camera Recording Manual Focus Auto Focus may not be able to focus on the subject in the situations shown below. In such situations, set the camcorder to Manual Focus mode and focus manually. Operation button Power Zoom control Subject is too dark. Lack of contrast, e. g. snow scene. DISPLAY/MODE SET button 1 2 In Camera mode, press the DISPLAY/ MODE SET button until the mode screen appears. Press l or m on the Operation button to select "FOCUS", then press the centre of the Operation button. M A NU A L S E T F OCUS AUTO F OCUS BLC / GA I N Fast-moving subject. Background is too bright. / Subject has horizontal stripes. Subject is being shot through a dirty or wet window. 3 Light reflects off the subject. Two subjects at different distances overlap in the same scene. Adjust the Power Zoom control to frame the subject as you desire. [. . . ] 28 T Tape speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Terminal cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Time Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 P Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]