User manual SHARP WF-5000W

[. . . ] Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. PORTABLE STEREO COMPONENT SYSTEM SYSTÈME STÉRÉO PORTABLE SISTEMA COMPONENTE DEL EQUIPO PORTÁTIL MODEL MODÈLE MODELO Nous vous remercions d'avoir porté votre choix sur ce produit SHARP. Pour en tirer le meilleur parti, veuillez lire ce mode d'emploi très attentivement. [. . . ] Within 30 seconds, press the MEMORY button to store that station in memory. Radio If the "MEMORY" and preset number indicators disappear before the station is memorised, repeat the operation from step 2. 5 Repeat steps 1 - 4 to set other stations, or to change a preset station. When a new station is stored in memory, the station previously memorised will be erased. Note: The backup function protects the memorised stations for a few hours should there be a power failure or the AC power lead disconnection. The International Telecommunication Union (ITU) has established that member countries should maintain either a 100 kHz or 50 kHz interval between broadcasting frequencies of FM stations and 10 kHz or 9 kHz for MW stations. The illustration shows the 50/9 kHz zones (regions 1 and 3), and the 100/10 kHz zone (region 2). This product is not equipped with a span selector. However, it will be adjusted to a 50 kHz FM (9 kHz MW) interval when shipped from the factory. Before using the unit, be sure to set it to the FM/MW tuning interval (span) used in your area. To change the FM/MW tuning interval: 1 Press the ON/STAND-BY button to turn the power on. 2 Press and hold down the TUNER (BAND) button, for 3 seconds. or 3 The display will appear for 2 seconds and the new setting is activated. Caution: When the unit is left for a few hours after the span has been switched and the AC power lead disconnected, the FM span will be automatically returned to 50 kHz (MW span to 9 kHz). When the span is switched, all the memorised stations will be cancelled. To recall a memorised station Press the PRESET ( desired station. or ) button for less than 0. 5 seconds to select the To scan the preset stations The stations saved in memory can be scanned automatically. (Preset memory scan) 1 Press the PRESET ( or ) button for more than 0. 5 seconds. The preset number will flash and the programmed stations will be tuned in sequentially, for 5 seconds each. 2 Press the PRESET ( or ) button again when the desired station is located. E-13 06/4/3 WF-5000W(U)3. fm TINSEA095AWZZ Listening to a cassette tape (TAPE 1 or TAPE 2) Before playback: For playback, use normal or low-noise tapes for the best sound. (Metal or CrO tapes are not recommended. ) Do not use C-120 tapes or poor-quality tapes, as they may cause malfunctions. Before loading a tape into the cassette compartment, tighten the slack with a pen or a pencil. Auto power off function: In the stop mode of tape operation, the main unit enters the stand-by mode after 15 minutes of inactivity. WF-5000W Continuous playback (TAPE 1 to TAPE 2) 1 2 3 4 Press the area marked " " and load cassettes into the TAPE 1 and TAPE 2 cassette compartments. Press the TAPE (1 2) button to select TAPE 1. button. ENGLISH Press the CONTINUOUS PLAYBACK Press the TAPE 1 button to start playback. Playback begins from side A on TAPE 1, the playback sequence will be as follows: TAPE 1 side A TAPE 2 side A TAPE 2 side B stop Tape 2 playback (two sides) 1 2 3 4 Tape 1 playback (one side) 1 2 3 4 5 Press the ON/STAND-BY button to turn the power on. Press the TAPE (1 2) button to select TAPE 1. [. . . ] Are the capstans, pinch rollers, or heads dirty?If a power failure occurs during playback, the heads remain engaged with the tape. Do not open the compartment with great force. Possible cause Is the erase-prevention tab removed? [. . . ]