User manual SHARP XE-A101

[. . . ] WARNING FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when this equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] Mode switch settings are made by sliding the switch . Z Reports The contents of Z reports are the same as those of X reports, but issuance of a Z report resets all the transaction totals to zero. To issue a Z report, set the mode switch to the Z/PGM position. If the secret code is programmed, you must enter the secret code and press this step. counter and total Percent counter and total Item void counter and total Void mode counter and total Taxable 1 total Tax 1 total Taxable 2 total Tax 2 total Taxable 3 total Tax 3 total Taxable 4 total Tax 4 total Count of transactions Sales total Cash sale total Check sale counter and total Charge sale counter and total Received-on-account total Paid-out total No sale counter Cash in drawer Clerk 1 sale total Clerk 2 sale total Clerk 3 sale total Clerk 4 sale total OFF REG VOID X/F Z/PGM D D For Z reports without grand total resetting Press You can select the following functions: REG: OFF: VOID: X/F: Permits transaction entries. Permits you to cancel transaction entries. Permits printing of sales reports and displaying of flash reports. Z/PGM: Permits printing of sales reports, resetting of sales data and programming. . If the secret code is programmed, you have to enter the secret code and press again after this step. For Z reports with grand total resetting If you want to reset the grand total(GT)when taking the Z report, press k instead of . Other than resetting the grand total, this report is the same as the normal Z reports. If the secret code is programmed, you have to enter the secret code and press k again after this step. , g or k. #/ SBTL Keyboard Layout SHIFT TAX1 SHIFT @/TM /RA TAX2 SHIFT /PO PLU CHK CLK# 7 8 3 2 4 6 #/ SBTL CH % CA/AT/NS VOID ESC 5 1 D press In order to enter the departments 5 to 8, SHIFT and then the 5 1 to 8 4 keys. is (o) Subtotal: This symbol appears when o pressed and the cash register computes the subtotal, and also when the amount tendered is less than the total sale amount. (c) Change: This symbol appears whenever the c change due amount is displayed. (l) Low battery: This symbol appears when the l power of the installed batteries is below a certain level or you need to replace the batteries with new ones. (see the "Maintenance" section for explanation. ) (l) No battery: This symbol appears when no l batteries are installed. (see "Maintenance" and "Getting Started" sections for explanation. ) In addition, the following appear when appropriate: · The minus sign (-) can appear in positions 2 to 8. · The decimal point appears in positions 1 to 3. · When entry of the secret code is necessary, "- - " appears in positions 1 to 4 . -- D Flash Reports (displayed but not printed) Press the following key in the X/F mode: Department Total Department key Sales Total Cash in Drawer #/ SBTL CH Programming Before you begin programming, set the mode switch to the Z/PGM position. Tax Programming Tax Table Programming If you are in an area that uses a tax table for tax calculation, you can program the cash register accordingly. Tax table programming can be performed for Tax 1 and Tax 2. Sample tax table 1 (6%): Tax . 00 . 01 . 02 . 03 . 04 . 05 . 06 . 07 . 08 . 09 . 10 . 11 . 12 . 13 Breakpoint Breakpoint difference . 01 . 11 . 23 . 39 . 57 . 73 . 89 1. 11 1. 23 1. 39 1. 57 1. 73 1. 89 2. 11 . 10 . 12 . 16 . 18 . 16 . 16 . 22 . 12 . 16 . 18 . 16 . 16 . 22 Non-cyclic OFF REG VOID X/F Z/PGM D Follow these steps as needed. If you do not press the key at the end of each programming step, you can continue programming without printing the programming report. #/ SBTL Programming by Departments Preset Unit Price The preset unit price function assigns a frequently purchased item to a department key and enables you to enter the price simply by pressing the department key. Specify a price using the following sequence: Unit Price (Max. key ( #/ SBTL Cyclic I ) Department Status You can specify various status parameters (+/- sign, single item cash sale function, taxable status and entry digit limit) for a department key. Use the following sequence: ABCDEFG @/TM Cyclic II Sample tax table 2: Tax . 00 . 01 . 02 . 03 . 04 . 06 . 09 . 10 . 11 . 12 . 14 . 17 Breakpoint . 01 . 11 . 26 . 47 . 68 . 89 1. 11 1. 26 1. 47 1. 68 1. 89 2. 11 Dept. [. . . ] Model: XE-A101 Specifications LIIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its original container, will be free from defective workmanship and materials and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof at no charge to the purchaser for parts or labor for the time period(s) set forth below. This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any product the exterior of which has been damaged or defaced, which has been subjected to misuse, abnormal service or handling or which has been altered or modified in design or construction. In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer. The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. [. . . ]