User manual SHARP XE-A206

[. . . ] 16 5:30 PM Page C2 WARNING FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] 0000), currency conversion rate entry method - open or preset (both are enabled) Compulsory entry of amount tender (not compulsory), entry digit limit (8 digits), footer printing (not printed) Entry digit limit (7 digits) Percent/discount calculation is applied to individual department and PLU/subdepartment. * Subtotal %/Subtotal _: Percent/discount calculation is applied to subtotals. Rate for %, & and V To program zero *Rate % & V or A To program another rate *: Rate 0. 9999 (Currency conversion rate) Key operation example Print 10 P 25 0 P 7674 % V A Percent rate Currency conversion rate You must use a decimal point when setting fractional rates. 00%) % & or A To program for another percent key • Percent entries that exceed the upper limit may be overridden in the MGR mode. The P key is needed only for fractional entry. Key operation example Print 15 s 29 @ P 00 % A Percentage limit Function parameters for %, & and To program “0” for all items *ABCDEFGH @ % & or A To program for another key 36 A206_3 FOR THE MANAGER 09. 16 5:31 PM Page 37 *: Item: A B C D E F G H Tax 4 status Tax 3 status Tax 2 status Tax 1 status +/- sign Item % / Item _ Subtotal % / Subtotal _ Entry digit limit for discount key Selection: Taxable Non-taxable* Taxable Non-taxable* Taxable Non-taxable* Taxable Non-taxable* + (premium) sign - (discount) sign* Allow* Disallow Allow* Disallow Entry: 1 0 1 0 1 0 1 0 0 1 0 1 0 1 0-7 (default: 7) When programming percent keys, always enter 0 for H. Tax status (taxable 1 through 4 / non-taxable) • When taxable is selected, tax is applied to the amount obtained after premium or discount calculation. +/- sign • Programming of the +/- sign assigns the premium or discount function for each key. Entry digit limit (For discount key only) • The entry digit limit is in effect for the REG mode operations but can be overridden in the MGR mode. The entry digit limit is represented by the number of allowable digit for the maximum entry amount for discount key. Key operation example Print 00011006 @ -A Tax status From left, FGH Sign(E) Function parameters for V To program “0” for all items *AB @ V Selection: Allow* Disallow Allow* Disallow A Entry: 0 1 0 1 *: Item: A B Open rate entry Preset rate entry Key operation example Print 00 @ VA From left, AB 37 A206_3 FOR THE MANAGER 09. 16 5:31 PM Page 38 Entry digit limit for r, R and t Entry digit limit @ r, R t or A (only for manual entry) • For r R, enter 0 to 9 (digits), and for t (manual tax), enter 0 to 7 (digits). By default, 9 for r and R and 7 for t are set. Entry digit limit is in effect for REG mode operation but can be overridden in MGR mode. The entry digit limit is represented by the number of allowable digits for maximum entry or total amount. When “0” is set, the operation of the corresponding key is prohibited. Key operation example Print 4@ RA Function parameters for C, c and A (when using as CA key) To program “0” for all items *1ABC @ s, C c or *2 A Entry: To program for another key *2:Press s key for CA key setting. *1:Item: A B Footer printing Amount tendered entry Selection: C Entry digit limit Allow 1 Disallow* 0 Compulsory 1 Non-compulsory (for the CA or CHK keys)* 0 Inhibit (for the CH key)* 0 0-8 (default: 8) Footer printing • This option decides whether or not the machine should print a message at the bottom of a receipt when a specified media key is used. to program a footer logo message , refer to “Logo messages” section on page 43. Amount tendered entry • You may select amount tendered, compulsory or optional, for the A and C keys. [. . . ] In case you need a new USB cable, order the USB cable manufactured by SHARP Co. (Part code: 0GS5422580) for use with the XE-A206. Use these labels with the department keys. Write department names on the labels and attach them to the department keys by first removing the transparent key covers. [. . . ]