User manual SHARP XG-C430X/C330X

[. . . ] LCD PROJECTOR MODEL XG-C430X XG-C330X SETUP MANUAL Setting up the Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Screen Size and Projection Distance . . . . . . . . . . . . . . . . 3 Throw Distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Standard Zoom Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If you did not change the IP address in "3. Setting up a Network Connection for the Projector" (pages 22-23), enter "http://192. 168. 150. 2/". 3 A screen for controlling the projector appears, ready for performing various status conditions, control, and settings. -24 Controlling the Projector via LAN Confirming the Projector Status (Status) Controlling the Projector (Control) On this screen, you can perform projector control. You can control the following items : On this screen, you can confirm the projector status. You can confirm the following items : · · · · · · · · · · · · MAC Address Power Condition Lamp Timer Lamp Life Input Signal Info Serial Number Power Input Select Volume AV Mute Note · If you click the "Refresh" button before the screen is displayed completely, an error message ("Server Busy Error") will be displayed. Wait for a moment and then operate again. · You cannot operate this page while the projector is warming up. · While the projector is in standby mode, you can only control "Power ON". · For details about each item, refer to the projector's operation manual. Note · If you click the "Refresh" button before the screen is displayed completely, an error message ("Server Busy Error") will be displayed. Wait for a moment and then operate again. · For details about each item, refer to the projector's operation manual. -25 Controlling the Projector via LAN Setting and Adjusting the Projector (Settings & Adjustments) Example: "Picture" screen display for INPUT 1 Setting the Security (Network ­ Security) On these screens, you can make projector settings or adjustments. You can set or adjust the following items : · · · · · · · · · · · · · · · · · · · · · · · · · · Picture Mode CLR Temp Progressive (Video) Signal Type (Computer, DVI) Dynamic Range (DVI) Video System (Video) Resolution Setting Auto Sync Resize Auto Keystone OSD Display Background Eco/Quiet Mode Auto Power Off System Sound Menu Position Direct Power On Password Internal Speaker Audio Out Projection Mode Fan Mode Monitor Out RS-232C Speed All Reset Language On this screen, you can make settings relating to security. Items Description User Name Setting of user name for security protection. Password Setting of password for security protection. Accept IP It is possible to set up to three Address IP addresses allowing connection to the projector. All IP No limits are set to IP addresses Addresses connecting to the projector. From only For security improvement, only an specific IP IP address set by "Address 1-3" addresses can be connected to the projector. Note · User Name and Password can be up to 8 characters. · You can input the characters below : a-z, A-Z, 0-9, -, _ Note · If you click the "Refresh" button before the screen is displayed completely, an error message ("Server Busy Error") will be displayed. Wait for a moment and then operate again. · You cannot operate this page while the projector is warming up. · For details about each item, refer to the projector's operation manual. -26 Controlling the Projector via LAN Making General Settings for the Network (Network General) Setting for Sending E-mail when an Error Occurs (Mail ­ Originator Settings) On this screen, you can make settings for sending e-mail to report when the projector has generated an error. On this screen, you can make general settings relating to the network. Items Projector Name Auto Logout Time Description Setting the projector name. Setting the time interval in which the projector will be automatically disconnected from the network in units of a minute (from 1 to 65535 minutes). If the set value is made 0, the Auto Logout function is disabled. [. . . ] (Example) When the IP address is "192. 168. 150. 2" and the subnet mask is "255. 255. 255. 0" for the projector, the IP address for the computer should be "192. 168. 150. X" (X=3-254) and the subnet mask should be "255. 255. 255. 0". Note · When "DHCP Client" is set to "OFF" on the projector IP address : 192. 168. 150. 2 Subnet mask : 255. 255. 255. 0 Gateway address : 0. 0. 0. 0 (Not Used) · For network settings for the projector, refer to page 22. -41 Troubleshooting \ Take the following steps for checking the network settings for the computer. · In the case of Windows® 98 or 98SE: click "START" "Programs" "MS-DOS Prompt" in order. · In the case of Windows® Me: click "START" "Programs" "Accessories" "MS-DOS Prompt" in order. · In the case of Windows® 2000: click "START" "Programs" "Accessories" "Command Prompt" in order. [. . . ]