User manual SHARP XG-C455W DATASHEET

[. . . ] Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. [. . . ] See page 50 for details. Saving Adjustment Settings This projector allows you to store up to seven adjustment settings for use with various computers. Select "Save Setting" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. -48 Selecting Adjustment Settings Adjustment settings stored in the projector can be easily accessed. Select "Select Setting" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. Note · If a memory has not been set, a resolution and frequency setting will not be displayed. · When selecting a stored adjustment setting with "Select Setting", you can set the projector in the stored adjustments. Special Mode Settings Ordinarily, the type of input signal is detected and the correct resolution mode is automatically selected. However, for some signals, the optimal resolution mode in "Special Modes" on the "Fine Sync" menu screen may need to be selected to match the computer display mode. Basic Operation Set the resolution by selecting "Special Modes" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. Note · Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering may occur, making the image hard to see. ) · When a DVD player or Digital Video is connected, select 480P as the input signal. · See "Checking the Input Signal" below for information on the currently selected input signal. Checking the Input Signal This function allows you to check the current input signal information. Select "Signal Info" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. Note · The projector will display the number of scanned lines available from audio-visual equipment such as a DVD player or Digital Video. -49 Adjusting Computer Images Auto Sync Adjustment Used to automatically adjust a computer image. Select "Auto Sync" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. Note When setting to " Normal" or High Speed": " · Auto Sync adjustment will occur when the projector is turned on or when the inputs are switched, when connected to a computer. Manual adjustments should be performed: · When the optimum image cannot be achieved with Auto Sync adjustment. menu is set to "sRGB". STANDARD CUSTOM PRESENTATION CINEMA 56 -56 Displaying Dual Pictures (Pict in Pict) Picture in Picture function allows you to display two pictures on the same screen. You can display the image input from INPUT 3 or 4 as an inset picture overlapping the main picture from INPUT 1 or 2. Displaying the Inset Picture 1 2 UNDO button Press . ENTER button Press or on the remote control or on the projector to switch the image in the inset picture . Press ', ", \ and | to set the position of the inset picture. · Press to stop the frame from moving or to make the frame disappear. ', ", \, | buttons PinP button INPUT 3/4 buttons 3 4 Press ture. to move the inset pic- · The inset picture will be moved to the inset picture frame. Note · The inset picture can only be displayed with composite video (NTSC/PAL/ SECAM) or S-Video signal. · The Freeze function works only with the inset picture, when the Pict in Pict mode is in operation. When the signal entered into INPUT 1 or 2 is as follows, Pict in Pict does not work: · With a resolution that exceeds SXGA. · When the input signal is 480I, 480P, 540P, 576I, 576P, 720P, 1035I or 1080I. · When the input signal has changed to the Interlace mode using RGB signals. · When the picture display mode is set to "DOT BY DOT". · When no signals are sent to INPUT 1 or 2, or when the resolution or refresh rate (vertical frequency) is changed. Easy to Use Functions -57 Black Screen Function This function can be used to display a black screen. Blacking out the Projected Image 1 2 Press . · The screen turns black and "BLACK SCREEN" is displayed on the screen. BLACK SCREEN button To return to the original projected image, press again. " Projected Image 58 -58 Displaying the Break Timer This function can be used to show the remaining time for break during meeting. Displaying and Setting the Break Timer ', ", \ , | 1 2 buttons Press . The break timer starts to count down from 5 minutes. When " " is displayed, press ' , " , \ or | to set the break timer. · You can set anywhere between 1 and 60 minutes (in 1 minute units). · The break timer starts to count down as soon as ' , " , \ or | is pressed. BREAK TIMER button 3 Press timer. to cancel the break "On-screen Display Note · Auto Power Off function will be temporarily disabled during the break timer. [. . . ] 71 RGB cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 RS-232C terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 -100 Save Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Select Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]