User manual SHARP XG-C58X

[. . . ] Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch. Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, suédois, espagnol, italien, néerlandais, portugais, chinois (chinois traditionnel et chinois simplifié), coréen et arabe. Veuillez lire attentivement ces instructions avant de faire fonctionner le projecteur. Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska, svenska, spanska, italienska, holländska, portugisiska, kinesiska (traditionell kinesiska och förenklad kinesiska), koreanska och arabiska. [. . . ] · In PAL50Hz or SECAM, the two-two pull down enhancement will be enabled only in the Film Mode, when the film source has been entered. · Basic Operation -47 Adjusting Computer Images Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in portions of the screen. Selected Item Clock Phase H-Pos V-Pos Adjusts vertical noise. Adjusts horizontal noise (similar to tracking on your VCR). Centers the on-screen image by moving it to the left or right. Centers the on-screen image by moving it up or down. Description When Auto Sync is OFF When "Auto Sync" is "OFF", interference such as flickering or vertical stripes may occur if displaying tilings or vertical stripes. Should this occur, adjust "Clock", "Phase", "H-Pos" and "V-Pos" for obtaining an optimum image. Select "Clock", "Phase", "H-Pos" or "VPos" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. Note · Computer image adjustments can be made . See page 50 for easily by pressing details. Saving Adjustment Settings This projector allows you to store up to seven adjustment settings for use with various computers. Select "Save Setting" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. -48 Selecting Adjustment Settings Adjustment settings stored in the projector can be easily accessed. Select "Select Setting" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. Note · If a memory position has not been set, a resolution and frequency setting will not be displayed. · When an image with a resolution higher than SXGA is displayed, "×2" and "×3" cannot be selected. "On-screen Display Easy to Use Functions 2 Press to cancel the operation, then the magnification returns to ×1. Note In the following cases, the image will return to the normal size (×1). · When the input signal is changed. · When the input signal resolution and refresh rate (vertical frequency) change. -55 Gamma Correction Function Gamma is an image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighter portions. When you are displaying images with frequent dark scenes, such as a film or concert, or when you are displaying images in a bright room, this feature makes the dark scenes easier to see and gives the impression of greater depth in the image. Selected Mode STANDARD PRESENTATION CINEMA CUSTOM For Standard picture Brightens darker portions of image for more enhanced presentations. Gives greater depth to darker portions of image for a more exciting theater experience. Allows you to adjust gamma value using Sharp Advanced Presentation Software. Description Adjusting Gamma Correction 1 Press . · Each time is pressed, the gamma level toggles between the different types of gamma modes. UNDO button GAMMA button 2 To return to the default settings, when "GAMMA" is press displayed. Note · The Gamma mode does not operate for INPUT 1 or INPUT 2 when "Color Selected" on the C. M. S. STANDARD CUSTOM PRESENTATION CINEMA 56 -56 Displaying Dual Pictures (Pict in Pict) Picture in Picture function allows you to display two pictures on the same screen. You can display the image input from INPUT 3 or 4 as an inset picture overlapping the main picture from INPUT 1 or 2. Displaying the Inset Picture 1 2 UNDO button Press . ENTER button Press or on the remote control or on the projector to switch the image in the inset picture . Press ', ", \ and | to set the position of the inset picture. · Press to stop the frame from moving or to make the frame disappear. ', ", \, | buttons PinP button INPUT 3/4 buttons 3 4 Press ture. to move the inset pic- · The inset picture will be moved to the inset picture frame. Note · The inset picture can only be displayed with composite video (NTSC/PAL/ SECAM) or S-Video signal. · The Freeze function works only with the inset picture, when the Pict in Pict mode is in operation. [. . . ] 71 RGB cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 RS-232C terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 -100 Save Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Select Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]