User manual SHARP XG-NV1E

[. . . ] 12 Setting up the Projector Network Environment . . . Connecting the Projector to a Computer . . . . . . . . . . Setting an IP Address for the Computer . . . . . . . . . . Setting up a Network Connection for the Projector . . . [. . . ] · While the projector is in standby mode, you can only control "Power ON". · For details about each item, refer to the projector's operation manual. Note · If you click the "Refresh" button before the screen is displayed completely, an error message ("Server Busy Error") will be displayed. Wait for a moment and then operate again. · For details about each item, refer to the projector's operation manual. -24 Controlling the Projector via LAN Setting and Adjusting the Projector (Settings & Adjustments) Example: "Picture" screen display for INPUT 1 Setting the Security (Network ­ Security) On these screens, you can make projector settings or adjustments. You can set or adjust the following items : · · · · · · · · · · · · · · · · · · · · · · · · · · · · Picture Mode CLR Temp Bright Boost Progressive C. M. S. Adjustment DNR Signal Type Auto Sync Auto Sync Disp Audio Out Internal Speaker [OFF][ON] Resize OSD Display Video System (INPUT 4/5) Background Startup Image Eco Mode [OFF][ON] Auto Search [OFF][ON] Auto Power Off [OFF][ON] Lamp Mode Projection Mode Keylock Level Set Inputs RS-232C Speed Monitor Out (Standby) OSD Language Video Wall (See page 41. ) Stack Setting (See page 38. ) On this screen, you can make settings relating to security. Items Description User Name Setting of user name for security protection. Password Setting of password for security protection. Accept IP It is possible to set up to three Address IP addresses allowing connection to the projector. No limits are set to IP addresses All IP Addresses connecting to the projector. From only For security improvement, only an specific IP IP address set by "Address 1-3" addresses can be connected to the projector. After clicking the "Apply" button, the set values appear. Confirm that the values are set properly, and then click the "Confirm" button. Note · After setting items, wait for 10 seconds and then re-access. This allows you to confirm that the settings for e-mail transmission are properly set. Note · E-mail Address can be up to 64 characters. · You can input the characters below : a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |, }, ~, _, ', . , @, ` (You can input "@" only one time. ) · For details about error items, refer to the projector's operation manual. -27 Setting the Projector Using RS-232C or Telnet Connect the projector to a computer using RS-232C or Telnet, and open the SETUP MENU on the computer to carry out various settings for the projector. 7 When Connecting Using RS-232C "Password:" is displayed. Input the password and press the "Enter" key. · If a password has not yet been set, just press the "Enter" key. 1 2 Launch general purpose terminal emulator. Input settings for the RS-232C port of the terminal emulator as follows. Baud Rate Data Length Parity Bit Stop Bit Flow Control : 9600 bps* : 8 bit : None : 1 bit : None 8 Input "setup" and press the "Enter" key. · SETUP MENU will be displayed. SETUP MENU ---------------------------------SETUP MENU-------------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup> * This is the factory default setting. If the value of Baud Rate for the projector has been changed, set Baud Rate here according to the changed value on the projector. Note · User name and password are not set in the factory default settings. · If the user name or password is entered incorrectly three times, SETUP MENU will be quit. 3 4 5 6 Input "PJS11234" and press the "Enter" key. Input "PJS25678" and press the "Enter" key within 10 seconds. Press the "Enter" key. "User Name:" is displayed. Input the user name and press the "Enter" key. · If a user name has not yet been set, just press the "Enter" key. -28 Setting the Projector Using RS-232C or Telnet SETUP MENU When Connecting Using Telnet ---------------------------------SETUP MENU-------------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup> 1 2 3 4 Click "start" from the Windows® desktop and select "Run". Enter "telnet 192. 168. 150. 2" in the text box that opens up. (If the IP address of the projector is 192. 168. 150. 2. ) Click the "OK" button. Note · If the IP address has been changed, ensure to enter the new IP address in step 2. [. . . ] · Gateway When the gateway setting for the projector is "0. 0. 0. 0" (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: · The subnets for the projector and the computer should be the same. · The IP address parts shown by the subnet mask for the projector and the computer should be the same. (Example) When the IP address is "192. 168. 150. 2" and the subnet mask is "255. 255. 255. 0" for the projector, the IP address for the computer should be "192. 168. 150. X" (X=3-254) and the subnet mask should be "255. 255. 255. 0". · Data Port Other computers should not use the data port of the projector. [. . . ]