User manual SHARP XG-NV5XU

[. . . ] Connecting the Projector to a Computer . . . . . . . . . . . Setting an IP Address for the Computer . . . . . . . . . . . . Setting up a Network Connection for the Projector . . 10 Quit without Saving Settings ([Q]Quit Unchanged) . . [. . . ] No limits are set to IP addresses All IP Addresses connecting to the projector. From only For security improvement, only an specific IP IP address set by "Address 1-3" address can be connected to the projector. Note · User Name and Password can be up to 8 characters. · You can input the characters below : a-z, A-Z, 0-9, -, _ Note · If you click the "Refresh" button before the screen is displayed completely, an error message ("Server Busy Error") will be displayed. Wait for a moment and then operate again. · You cannot operate this page while the projector is warming up. · For details about each item, refer to the projector's operation manual. -14 Controlling the Projector via LAN Making General Settings for the Network (Network General) Setting for Sending E-mail when an Error Occurs (Mail ­ Originator Setting) On this screen, you can make settings for sending e-mail to report when the projector has generated an error. On this screen, you can make general settings relating to the network. Items Projector Name Auto Logout Time Description Setting the projector name. Setting the time interval in which the projector will be automatically disconnected from the network in units of a minute (from 1 to 65535 minutes). If the set value is made 0, the Auto Logout function is disabled. Setting the TCP port number used when exchanging a data with the projector (from 1025 to 65535). Setting the port number used when searching for the projector (from 1025 to 65535). Input the user name and press the "Enter" key. · If a user name has not yet been set, just press the "Enter" key. 5 "Password:" is displayed. Input the password and press the "Enter" key. · If a password has not yet been set, just press the "Enter" key. 6 Input "setup" and press the "Enter" key. · SETUP MENU will be displayed. -18 Setting the Projector Using RS-232C or Telnet SETUP MENU SETUP MENU (Main Menu) ADVANCED SETUP MENU ADVANCED SETUP MENU ******************** ADVANCED SETUP MENU *********************** [1]Auto Logout Time [2]Data Port [5]Network Ping Test [6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3) [9]Accept All IP Addr [0]Search Port ---------------------------------SETUP MENU-------------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup> [!]Restore Default Setting [Q]Return to Main Menu [1]IP Address (Factory default setting : 192. 168. 150. 2) IP address settings. (Page 22) [2]Subnet Mask (Factory default setting : 255. 255. 255. 0) Subnet mask settings. (Page 22) [3]Default Gateway (Factory default setting : Not Used) Default gateway settings. (Page 22) [4]User Name (Factory default setting : Not Required) Setting of user name for security protection. (Page 23) [5]Password (Factory default setting : Not Required) Setting of password for security protection. (Page 23) [6] RS-232C Baud Rate (Factory default setting : 9600 bps) Baud rate settings for the RS-232C terminals. (Page 23) [7] Projector Name (Factory default setting : XGMB70X) It is possible to assign a projector name. (Page 23) [A]Advanced Setup Enters ADVANCED SETUP MENU. (Page 24) [D]Disconnect All Disconnect all connections. (Page 24) [V] View All Setting Displays all setting values. [. . . ] · IP Address Check that the IP address for the projector is not duplicated on the network. · Subnet Mask When the gateway setting for the projector is "0. 0. 0. 0" (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: · The subnet masks for the projector and the computer should be the same. (Example) When the IP address is "192. 168. 150. 2" and the subnet mask is "255. 255. 255. 0" for the projector, the IP address for the computer should be "192. 168. 150. X" (X=3-254) and the subnet mask should be "255. 255. 255. 0". · Gateway When the gateway setting for the projector is "0. 0. 0. 0" (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: · The subnets for the projector and the computer should be the same. [. . . ]