User manual SHARP XG-NV6XU

[. . . ] Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. [. . . ] · For details on Variable Audio Output (VAO) and Fixed Audio Output (FAO), see page 58. -28 Turning the Projector On/Off Connecting the Power Cord Plug the supplied power cord into the AC socket on the rear of the projector. Supplied accessory Power cord Turning the Projector on Before performing the steps in this section, connect any equipment that you use with the projector. (See pages 23-28. ) Info · English is the factory preset language. If you want to change the on-screen display to another language, change the language according to the procedure on page 62. Remove the lens cap and press projector or on the on the remote control. · The power indicator illuminates green. · After the lamp indicator illuminates, the projector is ready to start operation. · When System Lock is set, the keycode input screen appears. Enter the right keycode to start projection. See page 54 for details. ON button STANDBY button Power indicator Lamp indicator Note · The lamp indicator illuminates or blinks, indicating the status of the lamp. Blinking green: The lamp is warming up or shutting down. Red: The lamp is shut down abnormally or the lamp should be replaced. · When switching on the projector, a slight flickering of the image may be experienced within the first minute after the lamp has been illuminated. The screen can also be installed by inclining to that angle. · The Keystone Correction cannot be adjusted in the lateral direction. · You can use the same settings used in NORMAL mode 4:3 for 16:9. -31 3 Press . · The on-screen display of the Keystone Correction mode will disappear. · You can also use on the projector. Image Projection Adjusting the Focus This projector is equipped with an "Auto Focus" function that adjusts the focus automatically when it is turned on. When you want to readjust the focus after the Auto Focus function has been activated, you can operate the Auto Focus function using the following procedure. ZOOM/FOCUS button Adjustment buttons ('/"/\/|) AUTO FOCUS button Press on the projector or on the remote control. · The focus is adjusted automatically after which the focus pattern is displayed, and the focus pattern disappears from the screen. Note · Auto Focus can be performed over a range of 40 to 100 inches. ·The ability to adjust the focus automatically depends on the screen conditions and the surrounding brightness. · Adjust the focus manually when the focus is not adjusted with Auto Focus or when you want to make fine adjustments. When adjusting the focus using the buttons on the projector 1 Press . Auto focus sensor Auto focus may not function normally if there is an obstruction between the auto focus sensor and the screen, or if there is dirt or dust on the auto focus sensor. Remove any obstructions, dirt or dust. on the remote control Adjust by pressing the FOCUS buttons. FOCUS buttons ZOOM buttons AUTO FOCUS button 2 Adjust by pressing \ or |. · When not using the Auto Focus function, set "Auto Focus" on the "Options2" menu to "OFF". Adjusting the Projected Image Size When adjusting zoom using the buttons on the projector 1 Press . 2 Adjust by pressing ' or ". Note · Manually adjusting the focus or zoom After you have pressed the FOCUS buttons or ZOOM buttons on the remote control, or after you have pressed the ZOOM/FOCUS button on the projector, you can display the test pattern by pressing the ENTER button. The test pattern is useful for making more accurate adjustments. on the remote control Adjust by pressing the ZOOM buttons. -32 Switching the INPUT Mode Select the appropriate input mode for the connected equipment. Press , , or on the remote control to select the input mode. · When pressing ' or " on the projector, input mode switches in order of : INPUT buttons "On-screen Display of INPUT Mode (Example) INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 1/2 mode Using RGB Note · When no signal is received, "NO SIGNAL" will be displayed. When a signal that the projector is not preset to receive is received, "NOT REG. " will be displayed. [. . . ] 35 Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Power indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 PRJ mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 R-CLICK/UNDO button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]