User manual SHARP XG-NV7XU

[. . . ] Setting an IP Address for the Computer . . . . . . . . . . . . Setting up a Network Connection for the Projector . . 11 Quit without Saving Settings ([Q]Quit Unchanged) . . 22 IP Address Setting ([1]IP Address) . . . . . . . . . . . . . . . . . . . . . . [. . . ] Wait for a moment and then operate again. · You cannot operate this page while the projector is warming up. · For details about each item, refer to the projector's operation manual. -15 Controlling the Projector via LAN Making General Settings for the Network (Network General) Setting for Sending E-mail when an Error Occurs (Mail ­ Originator Settings) On this screen, you can make settings for sending e-mail to report when the projector has generated an error. On this screen, you can make general settings relating to the network. Items Projector Name Auto Logout Time Description Setting the projector name. Setting the time interval in which the projector will be automatically disconnected from the network in units of a minute (from 1 to 65535 minutes). If the set value is made 0, the Auto Logout function is disabled. Setting the TCP port number used when exchanging data with the projector (from 1025 to 65535). Setting the port number used when searching for the projector (from 1025 to 65535). Items SMTP Server Setting example / Remarks Setting an SMTP server address for e-mail transmission. e. g. 1 : 192. 168. 150. 253 e. g. 2 : smtp123. sharp. co. jp * When using a domain name, make settings for the DNS server. · If the user name or password is entered incorrectly three times in steps 4 or 5, SETUP MENU will be quit. "User Name:" is displayed. Input the user name and press the "Enter" key. · If a user name has not yet been set, just press the "Enter" key. 5 "Password:" is displayed. Input the password and press the "Enter" key. · If a password has not yet been set, just press the "Enter" key. 6 Input "setup" and press the "Enter" key. · SETUP MENU will be displayed. -19 Setting up the Projector Using RS-232C or Telnet SETUP MENU SETUP MENU (Main Menu) ADVANCED SETUP MENU ADVANCED SETUP MENU ******************** ADVANCED SETUP MENU *********************** [1]Auto Logout Time [2]Data Port [5]Network Ping Test [6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3) [9]Accept All IP Addr [0]Search Port ---------------------------------SETUP MENU-------------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup> [!]Restore Default Setting [Q]Return to Main Menu [1]IP Address IP address settings. (Page 23) [2]Subnet Mask Subnet mask settings. (Page 23) [3]Default Gateway Default gateway settings. (Page 23) [4]User Name (Factory default setting : Not Required) Setting of user name for security protection. (Page 23) [5]Password (Factory default setting : Not Required) Setting of password for security protection. (Page 24) [6]RS-232C Baud Rate (Factory default setting : 9600 bps) Baud rate settings for the RS-232C terminals. (Page 24) [7]Projector Name It is possible to assign a projector name. (Page 24) [8]DHCP Client DHCP Client settings. (Page 24) [A]Advanced Setup Enters ADVANCED SETUP MENU. [. . . ] · The IP address parts shown by the subnet mask for the projector and the computer should be the same. (Example) When the IP address is "192. 168. 150. 2" and the subnet mask is "255. 255. 255. 0" for the projector, the IP address for the computer should be "192. 168. 150. X" (X=3-254) and the subnet mask should be "255. 255. 255. 0". · Gateway When the gateway setting for the projector is "0. 0. 0. 0" (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: · The subnets for the projector and the computer should be the same. · The IP address parts shown by the subnet mask for the projector and the computer should be the same. [. . . ]