User manual SHARP XG-P10XU

[. . . ] 13 RS-232C Specifications and Commands . . . . . . . . 14 Setting up the Projector Network Environment . . . Connecting the Projector to a Computer . . . . . . . . . . Setting an IP Address for the Computer . . . . . . . . . . [. . . ] When connecting the projector to a hub, use a straight-through cable. 1 2 Start Internet Explorer (version 5. 0 or later) on the computer. Enter "http://" followed by the projector IP address set by the procedure on page 25 followed by "/" in "Address", and then press the "Enter" key. · The factory default setting for the projector : "DHCP Client" is "OFF" and IP address is "192. 168. 150. 2". If you did not change the IP address in "3. Setting up a Network Connection for the Projector" (pages 24, 25), enter "http://192. 168. 150. 2/". 3 A screen for controlling the projector appears, ready for performing various status conditions, control, and settings. -26 Controlling the Projector via LAN Confirming the Projector Status (Status) Controlling the Projector (Control) On this screen, you can perform projector control. You can control the following items : On this screen, you can confirm the projector status. You can confirm the following items : · · · · · · · · · · · · · · · MAC Address Power Condition Lamp Timer 1 Lamp Timer 2 Lamp Life 1 Lamp Life 2 Input Signal Info Serial Number Power Input Select Volume Mute (Audio) Shutter Note · If you click the "Refresh" button before the screen is displayed completely, an error message ("Server Busy Error") will be displayed. Wait for a moment and then operate again. · You cannot operate this page while the projector is warming up. · While the projector is in standby mode, you can only control "Power ON". · For details about each item, refer to the projector's operation manual. Note · If you click the "Refresh" button before the screen is displayed completely, an error message ("Server Busy Error") will be displayed. Wait for a moment and then operate again. e. g. 1 : 192. 168. 150. 253 e. g. 2 : smtp123. sharp. co. jp * When using a domain name, make settings for the DNS server. Setting the projector's e-mail address. The e-mail address set here becomes Originator E-mail Address. The name set here appears in the "Originator Name" column of the body of the message. Originator E-mail Address Originator Name Data Port Search Port Note · SMTP Server, Originator E-mail Address and Originator Name can be up to 64 characters. · You can input the characters below: SMTP Server and Originator E-mail Address : a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |, }, ~, _, ', . , @, ` (You can input "@" only one time for "Originator E-mail Address". ) Originator Name : a-z, A-Z, 0-9, -, _, (, ), space · If the settings of "3. Setting up a Network Connection for the Projector" on pages 24 and 25 are incorrectly set, e-mail will not be sent. -29 After clicking the "Apply" button, the set values appear. Confirm that the values are set properly, and then click the "Confirm" button. Note · After setting items, wait for 10 seconds and then re-access. · Projector Name can be up to 12 characters. · You can input the characters below : A-Z, 0-9, -, _, (, ), space (When "a-z" are input, they are converted to "A-Z" automatically. ) Controlling the Projector via LAN Setting Error Items and Destination Addresses to which E-mail is to be Sent when an Error Occurs (Mail ­ Recipient Settings) Setting Error Items and the URL that are to be Displayed when an Error Occurs (Service & Support ­ Access URL) On this screen, you can input e-mail destinations to which error notification (error items) e-mails are sent. Items E-mail Address Description Set addresses to which error notification e-mail is sent. Error Mail Error e-mail is sent on the error (Lamp, Temp, items checked in their check Fan, Cover) boxes. [. . . ] · IP Address Check that the IP address for the projector is not duplicated on the network. · Subnet Mask When the gateway setting for the projector is "0. 0. 0. 0" (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: · The subnet masks for the projector and the computer should be the same. · The IP address parts shown by the subnet mask for the projector and the computer should be the same. (Example) When the IP address is "192. 168. 150. 2" and the subnet mask is "255. 255. 255. 0" for the projector, the IP address for the computer should be "192. 168. 150. X" (X=3-254) and the subnet mask should be "255. 255. 255. 0". [. . . ]