User manual SHARP XG-P20XE

[. . . ] Important Information Setup & Connections Operation Buttons Multiple Function Basic Operation Maintenance & Troubleshooting Appendix OPERATION MANUAL XG-P20XE MODEL LCD PROJECTOR This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/ EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/EEG. [. . . ] · When the projector is connected to a computer by a USB mouse cable, you can still operate the mouse even if the projector is unplugged. (However, only when GyroRemote is not connected to the projector by wired remote control cable. ) 2 Release your finger from GYRO ACTIVE. The mouse cursor will stop moving around. GYRO ACTIVE 35 Setting up GyroRemote The projector uses RF channel and TEACH/LEARN settings to recognize individual projectors that may be operating in the same area, and keep them from interfering with each other. One GyroRemote can operate multiple projectors or you can even use multiple GyroRemotes to control one projector. Setting RF channels GyroRemote uses radio signals, which can receive interference under certain conditions. To avoid interference, you can switch RF channels. GyroRemote has 4 channels. GyroRemote Confirming the present RF channel 1 Press RF CH cover. LED located on the front, inside the upper Operation Buttons 2 The current channel in use is displayed on the lower right of the screen. You can also confirm the RF channel by the number of times the LED flashes. (Ex: RF Channel 3 if the LED flashes 3 times. ) Switching RF channels 1 Press RF CH RF CH for over 1 sec. 2 Each time you press for over 1 sec. the RF channel changes as shown below. 1 2 3 4 3 Each time you change RF channels it is displayed in the lower right of the screen. On-screen Display · An auto-search is performed on the projector side, so there is no need for manually adjusting the projector. 36 Setting up GyroRemote TEACH/LEARN · Each GyroRemote has its own ID code, which must be recognized by the projector that is going to be used. · The projector only recognizes the signal of the GyroRemote whose ID code has been input. Signals from other projectors or GyroRemotes that may be operating in the same area are not allowed to interrupt each other. Projector GyroRemote 1 Press LEARN on the projector. 2 While "Do you want to LEARN?" is displaying, press ENTER. You are now in LEARN mode. CAUTION · Entering LEARN mode erases all previously registered GyroRemotes data. You must re-enter each GyroRemote ID code in order for the projector to recognise them again. ENTER 3 Press TEACH located on the front, inside the upper Operation Buttons TEACH LEARN cover on the remote within 5 minutes. "Register" will appear on the display and you can now start using the GyroRemote with the projector. 4 To exit from the LEARN mode, press LEARN. · LEARN mode will exit if the LEARN is pressed or 5 minutes has elapsed. Operating multiple projectors with one GyroRemote On-screen Display CAUTION · Be aware that you can operate multiple projectors with one GyroRemote, even if you are in another room, as long as you stay within a 30 m range of the projector. 1 Set projector to LEARN mode. You use. can now operate multiple projectors with one GyroRemote. 3 Perform steps 1 and 2 for each projector you plan to 4 To exit from LEARN mode, press LEARN. · For setting multiple units in LEARN mode at one time, perform step 1 above for all projectors. · When a GyroRemote is registered with more than one projector, you can operate the screen pointer and other tools on all projectors at the same time. However, depending on RF conditions in the area, pointer positions may vary slightly between projectors. Using multiple GyroRemotes to operate one projector One projector can recognize up to 8 GyroRemote ID codes. 1 Set projector to LEARN mode. 2 Press TEACH on all GyroRemotes being used. Once the eighth GyroRemote is registered to operate one projector, the LEARN mode automatically finishes. [. . . ] 59 G GAMMA button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 GUI (Graphical User Interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 GyroRemote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 U UNDO button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]