User manual SHARP XG-P560W-N SETUP GUIDE

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. NOTE The laser component of the UX-1000/1100 is rated Class 1 and complies with 21 CFR 1040. 10 and 1040. 11 of the CDRH standards. [. . . ] 14 sec. Quiet Detect Time (Initial setting: 4 sec. ) Answering machine answers Sender presses start key (Line goes silent) Fax reception begins Testing for proper operation If needed, test the operation of the hookup as follows. 1 Call your fax machine from an outside phone line. Cover the mouthpiece to ensure that no sounds are transmitted to the fax machine. Your should hear your outgoing message, the beep to leave a message, and then a fax tone four seconds later (four seconds is the initial Quiet Detect Time setting). If you hear a fax tone, the hookup is operating properly. If the line is disconnected before you hear a fax tone, lower the Quiet Detect Time setting to three seconds and then call your fax machine again. 47 2 3 Chapter 7 Answering Machine Hookup 4 If you still do not hear a fax tone, turn off the Quiet Detect Time function and have callers send faxes by pressing "5", "*", "*" and then their Start key. For more information on this method, see "If it still doesn't work" in this chapter. If you have problems If you have problems with the hookup, first check the following: Is the answering machine connected properly to the fax?One end of the answering machine line should be inserted in the "TEL. SET" jack on the fax, and the other end in the answering machine's telephone line jack. Have you set Option Setting 9, TAD CONNECTED, to YES on your fax as described on the second page of this chapter, and is the reception mode set to AUTO?If the above settings and connections are correct and the hookup still doesn't operate properly, the operation of the fax and the answering machine are probably not synchronized well. No one is available to take your call right now. After the beep, please leave a message, or, if you want to send a fax, press 'five' once, 'asterisk' twice, and then your facsimile Start key. " 49 Chapter 7 Answering Machine Hookup How fax transmissions are detected: Your fax detects fax transmissions in two ways when an answering machine is connected, depending on whether the document is being sent automatically or manually: Automatic dialing: If the document is sent using a form of automatic dialing, such as Rapid Key or Speed Dialing, the transmitting fax machine will send a "calling tone" at 3-second intervals for a period of about 30 to 40 seconds after dialing. When your fax detects this tone, it will disconnect the answering machine, send a "reception tone" in response, and begin receiving the transmission. If the transmitting fax does not receive a reception tone from your fax within 30 to 40 seconds after dialing, it will usually hang up and automatically redial several minutes later. Since your fax may not be able to detect the transmitting fax's calling tone until after the outgoing message ends, it is important that the answering machine answers the call within two rings and the outgoing message is less than 10 seconds. Otherwise, your fax may not be able to establish communication with the transmitting fax before the latter hangs up. Manual dialing: If the document is being sent by normal (manual) dialing, the transmitting fax machine does not send a calling tone. Instead, the person faxing normally waits until they hear a reception tone and then presses their Start key. In the case of an answering machine hook-up, they will hear your outgoing message instead of a reception tone, and then press their Start key. However, this does not signal a fax transmission to your fax. Instead, your fax must use a function called "Quiet Detect Time" to detect the transmission. [. . . ] Cuando se oiga un tono de fax, presione START y cuelgue el receptor, o puede esperar a que aparezca RECEIVING en el visualizador, entonces cuelgue. Cargar el papel 1. Si todavía no está instalada, insertar la bandeja de papel en el fax. Retirar la cubierta, si se encuentra en la bandeja. (Para papel de tamaño folio, levantar la pieza de prolongación de la bandeja. ) 3. [. . . ]