User manual SHARP XG-PH70X DATASHEET

[. . . ] 12 Setting up the Projector Network Environment . . . Connecting the Projector to a Computer . . . . . . . . . . Setting an IP Address for the Computer . . . . . . . . . . Setting up a Network Connection for the Projector . . . [. . . ] Wait for a moment and then operate again. · You cannot operate this page while the projector is warming up. · While the projector is in standby mode, you can only control "Power ON". · For details about each item, refer to the projector's operation manual. Note · If you click the "Refresh" button before the screen is displayed completely, an error message ("Server Busy Error") will be displayed. Wait for a moment and then operate again. · For details about each item, refer to the projector's operation manual. -24 Controlling the Projector via LAN Setting and Adjusting the Projector (Settings & Adjustments) Example: "Picture" screen display for INPUT 1 Setting the Security (Network ­ Security) On these screens, you can make projector settings or adjustments. You can set or adjust the following items : · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Picture Mode CLR Temp Bright Boost Progressive C. M. S. Adjustment DNR Signal Type Auto Sync Auto Sync Disp Audio Out Internal Speaker Resize OSD Display Video System (INPUT 4/5) Background Startup Image Eco Mode Auto Search Auto Power Off Password Lamp Mode Projection Mode Keylock Level Set Inputs Fan Mode Direct Power On RS-232C Speed Monitor Out (Standby) Video Wall (See page 41. ) Stack Setting (See page 38. ) All Reset OSD Language On this screen, you can make settings relating to security. Items Description User Name Setting of user name for security protection. Password Setting of password for security protection. Accept IP It is possible to set up to three Address IP addresses allowing connection to the projector. All IP No limits are set to IP addresses Addresses connecting to the projector. · You can input the characters below : A-Z, 0-9, -, _, (, ), space (When "a-z" are input, they are converted to "A-Z" automatically. ) -26 Controlling the Projector via LAN Setting Error Items and Destination Addresses to which E-mail is to be Sent when an Error Occurs (Mail ­ Recipient Settings) Setting Error Items and the URL that are to be Displayed when an Error Occurs (Service & Support ­ Access URL) On this screen, you can input e-mail destinations to which error notification (error items) e-mails are sent. Items E-mail Address Description Set addresses to which error notification e-mail is sent. Error Mail Error e-mail is sent on the error (Lamp, Temp, items checked in their check Fan, Cover) boxes. This allows you to confirm that the settings for e-mail transmission are properly set. On this screen, you can make settings of the URL and error items that are to be displayed when the projector has generated an error. Items Access URL Description Set the URL that is to be displayed when an error occurs. Condition The URL is displayed when an (Always, Lamp, error checked in their check Temp, Fan, Cover) boxes occurs. This allows you to confirm that the URL site is properly displayed. Example of the display when an error occurs Note · E-mail Address can be up to 64 characters. · You can input the characters below : a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |, }, ~, _, ', . , @, ` (You can input "@" only one time. ) · For details about error items, refer to the projector's operation manual. -27 Setting the Projector Using RS-232C or Telnet Connect the projector to a computer using RS-232C or Telnet, and open the SETUP MENU on the computer to carry out various settings for the projector. 7 When Connecting Using RS-232C "Password:" is displayed. Input the password and press the "Enter" key. · If a password has not yet been set, just press the "Enter" key. 1 2 Launch general purpose terminal emulator. Input settings for the RS-232C port of the terminal emulator as follows. Baud Rate Data Length Parity Bit Stop Bit Flow Control : 9600 bps* : 8 bit : None : 1 bit : None 8 Input "setup" and press the "Enter" key. · SETUP MENU will be displayed. SETUP MENU ---------------------------------SETUP MENU-------------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup> * This is the factory default setting. If the value of Baud Rate for the projector has been changed, set Baud Rate here according to the changed value on the projector. Note · User name and password are not set in the factory default settings. · If the user name or password is entered incorrectly three times, SETUP MENU will be quit. 3 4 5 6 Input "PJS11234" and press the "Enter" key. Input "PJS25678" and press the "Enter" key within 10 seconds. [. . . ] · Gateway When the gateway setting for the projector is "0. 0. 0. 0" (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: · The subnets for the projector and the computer should be the same. · The IP address parts shown by the subnet mask for the projector and the computer should be the same. (Example) When the IP address is "192. 168. 150. 2" and the subnet mask is "255. 255. 255. 0" for the projector, the IP address for the computer should be "192. 168. 150. X" (X=3-254) and the subnet mask should be "255. 255. 255. 0". · Data Port Other computers should not use the data port of the projector. [. . . ]