User manual SHARP XG-PH70X-N SETUP GUIDE

[. . . ] ONLY WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. CAUTION RISK OF ELECTRIC SHOCK. DO NOT REMOVE SCREWS EXCEPT SPECIFIED USER SERVICE SCREWS. [. . . ] E-26 Menu Bars Items on the INPUT 1 or 2 Mode Menu Bar Main menu Picture ( ) Contrast Bright Color Tint Sharp Red Blue Reset CLR Temp 5500k 6500k 7500k 8500k 9300k 10500k Gamma Standard Black Detail White Detail Brighten White Emphasis [ON/OFF] Picture Setting Memory 1 Memory 2 Memory 3 Memory 4 Memory 5 Memory OFF Fine Sync ( ) Clock Phase 30 15 30 30 30 15 30 30 PRJ Mode ( ) Front Front Rear Rear Ceiling Ceiling 30 30 30 30 30 30 30 Sub menu 30 30 30 30 30 30 30 Main menu Language ( ) Sub menu English Deutsch Espaol Nederlands Franais Italiano Svenska Portugus Basic Operation H-Pos V-Pos Reset Special Modes Auto Sync Signal Info 640 720 480 480 640 480 37. 5 kHz 72 Hz [ON/OFF] Resolution Hor Freq Vert Freq Options ( ) Digital Shift Subtitle Reset Lamp Timer 30 10 30 10 * OSD Display [ON/OFF] Signal Type RGB Component Background Blue None Auto Power Off [ON/OFF] Menu Position Center Upper Right Lower Right Upper Left Lower Left Menu Color Opaque Translucent * The "Digital Shift" and "Subtitle" cannot be adjusted when Keystone correction is applied. The resolution, vertical frequency and horizontal frequency figures displayed above are for example purposes only. "Color", "Tint", and "Sharp" do not appear when "RGB" is selected in INPUT 2 mode. Only the items highlighted in the tree charts above can be adjusted. To adjust the items under the sub menu, press after selecting the sub menu. "Signal Type" is not displayed when using INPUT 1. "Contrast", "Bright", "Color", "Tint", "Sharp", "Clock", "Phase", "H-Pos", "V-Pos", "CLR-Temp", "Gamma", "Special Modes" and "Auto Sync" cannot be used in the DIGITAL INPUT mode. "Clock", "Phase", "H-Pos" and "V-Pos" cannot be used in the Component mode. E-27 Menu Bars Items on the INPUT 3 or 4 Mode Menu Bar Main menu Picture ( ) Contrast Bright Color Tint Sharp Red Blue Reset CLR Temp 5500k 3D Progressive 6500k 7500k 3D Progressive 8500k 3D Progressive 9300k 3D Progressive 10500k 3D Progressive Gamma Standard 3D Progressive Black Detail 3D Progressive White Detail 3D Progressive 3D Progressive Brighten White Emphasis [ON/OFF] Picture Setting 3D Progressive Memory 1 Memory 2 3D Progressive Memory 3 3D Progressive Memory 4 3D Progressive Memory 5 3D Progressive Memory OFF 3D Progressive Options ( ) Digital Shift Subtitle Reset Lamp Timer OSD Display [ON/OFF] Video Systems Auto PAL NTSC3. 58 SECAM NTSC4. 43 PALM PALN PAL60 Background Blue None Auto Power Off [ON/OFF] Menu Position Center Upper Right Lower Right Upper Left Lower Left Menu Color Opaque Translucent 30 10 30 10 PRJ Mode ( ) Front Front Rear Rear Ceiling Ceiling 30 30 30 30 30 30 30 Sub menu 30 30 30 30 30 30 30 Main menu Language ( ) Sub menu English Deutsch Espaol Nederlands Franais Italiano Svenska Portugus * Basic Operation * The "Digital Shift" and "Subtitle" cannot be adjusted when Keystone correction is applied. Only the items highlighted in the tree charts above can be adjusted. To adjust the items under the sub menu, press after selecting the sub menu. "Tint" cannot be used with PAL, SECAM, PAL-M, PAL-N or PAL-60. E-28 Adjusting the Picture You can adjust the projector's picture to your preferences with the following picture settings. To save the settings, select a memory from 1 to 5 and OFF (see page 32) and then adjust the settings. Description of Adjustment Items Selected item Contrast Brightness Color Tint Sharp Red Blue CLR Temp Gamma White Emphasis Picture Setting Reset button button For less contrast For more contrast For less brightness For more brightness For less color intensity For more color intensity Skin tones become purplish Skin tones become greenish For less sharpness For more sharpness For weaker red For stronger red For weaker blue For stronger blue For selecting a desired item from six color temperature settings For selecting a desired item from four gamma positions For switching "on" or "off" the function that emphasizes bright portions of the image For storing all items set in "Picture" All image adjustment items are returned to the factory preset settings. 2, 3 1, 4 On-screen Display e. Four gamma settings are available to allow for differences in the brightness of the room. Description of Gamma Modes Selected Mode Standard Description Standard picture without gamma correction Gives greater depth to darker portions of images for a more exciting theater experience. Emphasizes the gradation of the intermediate to high brightness portions of the image for more detailed expression. Brighten the darker portions of images for easier viewing in a dimly lit room. 4 2, 3 1, 5 Black Detail White Detail Brighten On-screen Display 1 Press MENU. The "Picture" menu screen appears. 3 Press / / to select "Gamma", and then press to select the desired gamma mode. 4 Press ENTER to save the setting. 5 To exit the menu screen, press MENU. Basic Operation Gamma cannot be used in the DIGITAL INPUT mode. Standard Black Detail Brighten White Detail E-31 Adjusting the Picture Picture Setting Function This function stores all items set in "Picture". Five settings can be stored separately in "Memory 1" to "Memory 5". Each stored setting is reassigned to each input mode (INPUT 1 to INPUT 4 and DIGITAL). Even when the input mode or signal is changed, you can easily select optimal settings from the stored settings. 1 This function can be operated using the PICTURE SETTING button on the projector or on the remote control, as well as the OSD menu screen. Description of Picture Setting Selected item Memory 1-5 Description Settings of all items in "Picture" can be stored for the respective input modes. The stored settings can be selected in any input modes. [. . . ] After the ninety (90) day warranty period on the Projector Lamp, parts and labor for a lamp replacement are the responsibility of the consumer. Cleaning of Optical System and/or replacement of any filter. Labor & materials required to remove and reinstall a suspended projector in installations not accessible with a standard (8' step) ladder or ceilings exceeding 12' in height. Labor & materials required to remove and reinstall a projector in complex systems including, but not limited to, projectors installed in custom enclosures, projectors connected to third party control and automation systems, and realignment of projectors installed in "mirrored" rear projection enclosures. [. . . ]