User manual SHARP XG-PH80W-N

[. . . ] DATA PROJECTOR MODEL XG-PH80W-N XG-PH80X-N SETUP MANUAL Setting up the Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Screen Size and Projection Distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Connecting Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 RS-232C Specifications and Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Setting up the Projector Network Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 1. Connecting the Projector to a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting an IP Address for the Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting up a Network Connection for the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The following procedure is for making settings on the computer. Network settings on the computer 1. Connecting the projector to a computer Connect a LAN cable (Category 5, cross-over type) between the computer and projector. LAN cable (commercially available) Page 19 2. Setting an IP address for the computer Adjust the IP settings of the computer to enable one-to-one communications with the projector. Temporarily change the computer's IP address. Pages 20, 21 3. Setting up a network connection for the projector Adjust the projector network settings to conform to your network. Use Internet Explorer (version 6. 0 or later) to make various projector settings. Pages 22, 23 · Microsoft®, Windows® and Windows Vista®are registered trademarks of Microsoft Corporation in the United States and/or other countries. · PJLink is a registered trademark or an application trademark in Japan, the United States, Canada, E. U. , China and/or other countries/regions. · All other company or product names are trademarks or registered trademarks of their respective companies. -18 Setting up the Projector Network Environment 1. Connecting the Projector to a Computer Establishing a one-to-one connection from the projector to a computer. Using a commercially available LAN cable (UTP cable, Category 5, cross-over type) you can configure the projector via the computer. 1 Disconnect the computer's LAN cable from the existing network. A LAN cable being connected to the network 2 Connect a commercially available LAN cable (UTP cable, Category 5, cross-over type) to the projector's LAN terminal and connect the other end of the cable to the computer's LAN terminal. LAN cable (cross-over type, commercially available) 3 Plug the power cord into the AC socket of the projector. 4 Turn on the computer. ON Info Confirm that the LINK LED on the rear of the projector illuminates. If the LINK LED does not illuminate, check the following: · The LAN cable is properly connected. · The power switches of both the projector and the computer are on. This completes the connection. Setting an IP Address for the Computer". -19 Setting up the Projector Network Environment 2. Setting an IP Address for the Computer The following describes how to make settings in Windows Vista®. 1 2 Log on the network using the administrator's account for the computer. Click "start", and click "Control Panel". 2 1 3 Click "View network status and tasks" of "Network and Internet", and click "View status" in the new window. · This manual uses examples to explain the operations in Category View. If you are using Classic View, double-click "Network and Sharing Center". 1 XXXXXXXXX 2 4 Click "Properties". · When the user account control display is displayed, click "Continue". 1 -20 Setting up the Projector Network Environment 5 Click "Internet Protocol Version 4 (TCP/IPv4)", and click the "Properties" button. 1 2 6 Confirm or change an IP address for the setup computer. 1 Confirm and note the current IP address, Subnet mask and Default gateway. Make sure to note the current IP address, Subnet mask and Default gateway as you will be required to reset them later. 2 Set temporarily as follows: IP address: 192. 168. 150. 3 Subnet mask: 255. 255. 255. 0 Default gateway: (Do not input any values. ) Note · The factory default settings for the projector are as follows: DHCP Client: OFF IP address: 192. 168. 150. 2 Subnet mask: 255. 255. 255. 0 Default gateway: 0. 0. 0. 0 7 After setting, click the "OK" button, and then restart the computer. After confirming or setting, proceed to "3. Setting up a Network Connection for the Projector". -21 Setting up the Projector Network Environment 3. Setting up a Network Connection for the Projector Settings for such items as the projector's IP address and subnet mask are compatible with the existing network. Set each item on the projector as follows. (See page 54 of the projector's operation manual for setting. ) DHCP Client: Off IP Address: 192. 168. 150. 002 Subnet Mask: 255. 255. 255. 000 1 Start Internet Explorer (version 6. 0 or later) on the computer, and enter "http://192. 168. 150. 2/system. html" in "Address", and then press the "Enter" key. [. . . ] · The IP address parts shown by the subnet mask for the projector and the computer should be the same. (Example) When the IP address is "192. 168. 150. 2" and the subnet mask is "255. 255. 255. 0" for the projector, the IP address for the computer should be "192. 168. 150. X" (X=3-254) and the subnet mask should be "255. 255. 255. 0". · Gateway When the gateway setting for the projector is "0. 0. 0. 0" (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: · The subnets for the projector and the computer should be the same. · The IP address parts shown by the subnet mask for the projector and the computer should be the same. [. . . ]