User manual SHARP XG-PH80WN BROCHURE

[. . . ] Note that Sharp Advanced Presentation Software Professional Edition is subject to change without prior notice for upgrading and improvement. The latest information on this software can be found at the following web site: http://www. sharp-world. com/projector/ G Microsoft and Windows are registered trademarks of Microsoft Corporation, USA. G All other brand or product names are trademarks or registered trademarks of their respective holders. G Great effort has been expended to ensure that the descriptions in this manual are correct. [. . . ] Password Input area 2 3 Select the Projector ID by clicking ". Input the new name in the "Projector Name Input area" or "Unique Name Input area". 42 Multi 4 5 Input the password. When the password has been set in the projector, the "Password Input area" is displayed. Once displayed, enter the password. Click "OK" or "Apply". G The "Projector Name" is a name for facilitating identification of the individual projectors when controlling multiple projectors. We recommend entering the projector's model name, the place where it is installed, etc. , in "Projector Name". G The "Unique Name" does not affect projector control. It is protected by the password set on page 37. (Only those who know the password can change it. ) We recommend inputting the name of the projector's owner, etc. , at "Unique Name". Adjusting and Controlling 43 Multi E-mail Sending Function This software makes it possible to automatically send an e-mail message containing information concerning errors to a preset e-mail address should projector errors be detected. In addition to automatically sending e-mail messages when errors arise, it is also possible to periodically send e-mail messages containing information on the projector status. G The PC setting for e-mail (e. g. , LAN connection setting or Dial-up connection setting) at first is needed to use this function. G The information is attached to the e-mail messages as files in CSV format. G This function can only be used when this software is running on a personal computer. The file has the extension "lcd". ) Sending the "Projector Condition" e-mail message manually Click "Send E-mail" to send an e-mail message containing information on the projector conditions manually. 52 Single Multi Error Notification Function This software is equipped with a function for automatically notifying the computer running the SAPS software with error information when an error arises with the projector. If a major error arises, a warning window is displayed, as shown below. Adjusting and Controlling When the "Help" button is clicked, the "Help" window opens. G The Occurrence and Timing settings can be customized at "Send E-mail Setting" (page 50). Projector information is then forwarded either when problems arise or periodically according to the configuration. G If your projector is an XG-V10 Series, the XG-P20X or the XG-PH80WN projector, a warning window is immediately displayed whenever errors occur. G If your projector is a model other than the XG-V10 Series, the XGP20X or the XG-PH80WN, some time (up to about 3 minutes) is required from when the error occurs until the warning window is displayed. 53 Multi Projector Timer Control This function is for turning off the projector's power at a preset time. G This function can only be used when this software is running on a personal computer. G This function manages the time based on the computer's built-in clock, so it will not operate properly if the computer's clock setting is incorrect. 1 Select "Projector Timer Control" from "Control Option". The "Projector Timer Control" dialog box will open. 1 2 1 Enable/disable check box 2 List of all connected projectors 2 Click on the projector for which you want to set the timer. Multiple projectors can be selected by pressing the keyboard's control or shift key while selecting the projectors. 3 Click "Setting OFF Timer". The "Projector Timer Control" dialog box will open. 1 1 Enable/disable check box 54 Multi 4 5 6 Set the time you want the timer to turn off. Check the "Enable/disable check box". Click "OK". Adjusting and Controlling 55 Multi Backup Function This function automatically turns on the projector assigned in advance as the backup projector, when the projector goes into standby due to a malfunction. When the backup projector autostarts, the settings of the projector in which the error occurred are suitably sent to the backup projector, therefore the interruption of the presentation is reduced to a minimum. G This function can only be used when this software is running on a personal computer. [. . . ] Local Area Network Main menu item Simultaneous control of multiple projectors from PC. Operating panel for integrated control of projectors in multiple projector operation mode. Open file folder containing images to be transmitted to the projector (for Presentation Transfer) Set whether to control a single projector or multiple projectors. Main menu item When a password is set, some functions can only be changed by the person with the password. [. . . ]