User manual SHARP XG-SV200X

[. . . ] DATA PROJECTOR MODEL XG-SV100W XG-SV200X SETUP MANUAL Connecting Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 RS-232C Specifications and Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Operating the Projector Using the PJLinkTM Protocol . . . . . . . . . . . . . . . . . . 10 Setting up the Projector Network Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (See page 62 of the projector's operation manual for setting. ) DHCP Client: Off IP Address: 192. 168. 150. 002 Subnet Mask: 255. 255. 255. 000 1 Start Internet Explorer (version 6. 0 or later) on the computer, and enter "http://192. 168. 150. 2/" in "Address", and then press the "Enter" key. If a user name and a password have not yet been set, just click the "OK" button. · If a user name and a password have been set, input the user name and the password, and click the "OK" button. · If the user name or password is entered incorrectly three times, an error message will be displayed. · When you are using Internet Explorer 7 or later, other setup screen may be displayed. In this case, make the proper adjustments for the setup screen. 2 3 When the screen as shown on the right appears, click "TCP/IP". -15 Setting up the Projector Network Environment 4 The TCP/IP setting screen appears, ready for network settings for the projector. Items Setting example / Remarks New You can set the password to protect Password the TCP/IP setting. DHCP Client IP Address Select "ON" or "OFF" to determine whether to use DHCP Client. You can set this item when "DHCP Client" is set to "OFF". Factory default setting: 192. 168. 150. 2 Enter an IP address appropriate for the network. You can set this item when "DHCP Client" is set to "OFF". Factory default setting: 255. 255. 255. 0 Set the subnet mask to the same as that of the computer and equipment on the network. You can set this item when "DHCP Client" is set to "OFF". Factory default setting: 0. 0. 0. 0 * When not in use, set to "0. 0. 0. 0". Factory default setting: 0. 0. 0. 0 * When not in use, set to "0. 0. 0. 0". Subnet Mask Default Gateway DNS Server Note · Confirm the existing network's segment (IP address group) to avoid setting an IP address that duplicates the IP addresses of other network equipment or computers. If "192. 168. 150. 2" is not used in the network having an IP address of "192. 168. 150. XXX", you don't have to change the projector IP address. · For details about each setting, consult your network administrator. 5 6 Click the "Apply" button. The set values appear. Confirm that the values are set properly, and then click the "Confirm" button. · · · · Close the browser. After setting items, wait for about 15 seconds and then re-access. Change the IP address of the setting computer back to its original address, which you have noted down in Step 6-1 on page 14, and then connect the computer and the projector to the network. -16 Controlling the Projector via LAN After connecting the projector to your network, enter the projector IP address in "Address" on Internet Explorer (version 6. 0 or later) using a computer on the network to start a setup screen that will enable control of the projector via the network. Controlling the Projector Using Internet Explorer Complete connections to external equipment before starting the operation. (See pages 22-26 of the projector's operation manual. ) Complete the AC cord connection. (See page 26 of the projector's operation manual. ) Note · When connecting the projector to the LAN, use a commercially available LAN cable (UTP cable, Category 5, cross-over type). When connecting the projector to a hub, use a straight-through cable. 1 2 Start Internet Explorer on the computer. Enter "http://" followed by the projector IP address set by the procedure on page 16 followed by "/" in "Address", and then press the "Enter" key. · When "DHCP Client" is set to "Off" on the projector, IP address is 192. 168. 150. 2. [. . . ] (Example) When the IP address is "192. 168. 150. 2" and the subnet mask is "255. 255. 255. 0" for the projector, the IP address for the computer should be "192. 168. 150. X" (X=3-254) and the subnet mask should be "255. 255. 255. 0". Note · When "DHCP Client" is set to "Off" on the projector: IP address: 192. 168. 150. 2 Subnet mask: 255. 255. 255. 0 Gateway address: 0. 0. 0. 0 (Not Used) · For network settings for the projector, refer to page 15. -24 Troubleshooting Take the following steps for checking the network settings for the computer. · In the case of Windows® 2000: click "start" "Programs" "Accessories" "Command Prompt" in order. · In the case of Windows® XP, Windows Vista®: click "start" "All Programs" "Accessories" "Command Prompt" in order. After launching the command prompt, enter the command "ipconfig", and press the "Enter" key. Note · Communication may not be established even after carrying out the network settings for the computer. [. . . ]