User manual SHARP XG-V10WE

[. . . ] Important Information Setup & Connections Operation Buttons Basic Operation Useful Features & Network Function Maintenance & Troubleshooting Appendix OPERATION MANUAL XG-V10WE LCD PROJECTOR MODEL Lenses are sold separately. This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/ EWG und 73/23/EWG mit Änderung 93/68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/ 336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/ 23/EEG, gewijzigd door 93/68/EEG. [. . . ] However, for some signals, the optimal resolution mode in "Special Modes" on the "Fine Sync" menu screen may need to be selected to match the computer display mode. (Slide the MOUSE/ADJUSTMENT switch on the remote control to the ADJ. position. ) MOUSE ADJ. 1, 6 2, 3, 4 5 1. 2. 3 4. 5. 6 1 Press MENU. 2 Press ß/© to select "Fine Sync". (GUI) On-screen Display 3 Press / to select "Special Modes", and then press ©. 4 Press / to select the optimal resolution mode. 6 To exit from the GUI, press MENU. · Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering may occur, making the image hard to see. ) · When inputting DTV 480P or 1080i signals, select the corresponding type of signal in step 4 above. Basic Operation Projector Remote Control Checking the Input Signal This function allows you to check the current input signal information. 1, 4 2, 3 (Slide the MOUSE/ADJUSTMENT switch on the remote control to the ADJ. 2 Press ß/© to select "Fine Sync". 1. 2. 3 4. 5. 6 MOUSE ADJ. 3 Press / to select "Signal Info" to display the current input signal. (GUI) On-screen Display 4 To exit from the GUI, press MENU. 48 Adjusting the Computer Images (RGB menu only) Projector 1, 5 2, 3, 4 Remote Control Auto Sync Adjustment · Used to automatically adjust a computer image. · Auto Sync adjustment can be made manually by pressing AUTO SYNC, or automatically by setting "Auto Sync" to "ON" in the projector's GUI menu. When "Auto Sync" is set to "ON": · The sync adjustment is automatically made each time the projector is turned on while connected to a computer or the input selection is changed. · The Auto Sync adjustment setting previously made is cleared when the projector's setting is changed. (Slide the MOUSE/ADJUSTMENT switch on the remote control to the ADJ. position. ) MOUSE ADJ. AUTO SYNC button 1. 2. 3 4. 5. 6 (GUI) On-screen Display 1 Press MENU. 2 Press ß/© to select "Fine Sync". 3 Press / to select "Auto Sync". 4 Press ß/© to select "ON". 5 To exit from the GUI, press MENU. Basic Operation On-screen Display · Automatic adjustments can be made by pressing AUTO SYNC. · When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page 46. ) g f s During Auto Sync adjustment, the On-screen Display changes as shown on the left. · Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector. Auto Sync Display Function Normally, an image is not superimposed during Auto Sync adjustment. You can, however, choose to superimpose a background image during Auto Sync adjustment. (Slide the MOUSE/ADJUSTMENT switch on the remote control to the ADJ. [. . . ] 64 Transmission Speed (RS-232C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 U UNDO button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 USB mouse control cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 K Keylock Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]