User manual SHARP XGNV4SE OPERATION MANUAL

[. . . ] 4 Wide-zoom Lens (AN-C12MZ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Tele-zoom Lens (AN-C18MZ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Tele-zoom Lens (AN-C27MZ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Tele-zoom Lens (AN-C41MZ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Factory default setting: 0. 0. 0. 0 * When not in use, set to "0. 0. 0. 0". DNS Factory default setting: 0. 0. 0. 0 Server * When not in use, set to "0. 0. 0. 0". Note · Confirm the existing network's segment (IP address group) to avoid setting an IP address that duplicates the IP addresses of other network equipment or computers. If "192. 168. 150. 2" is not used in the network having an IP address of "192. 168. 150. XXX", you don't have to change the projector IP address. · For details about each setting, consult your network administrator. 5 6 Click the "Apply" button. The set values appear. Confirm that the values are set properly, and then click the "Confirm" button. · · · · Close the browser. After setting items, wait for 10 seconds and then re-access. Change the IP address of the setting computer back to its original address, which you have noted down in Step 6-1 on page 21, and then connect the computer and the projector to the network. -23 Controlling the Projector via LAN After connecting the projector to your network, enter the projector IP address in "Address" on Internet Explorer (version 5. 0 or later) using a computer on the network to start a setup screen that will enable control of the projector via the network. Controlling the Projector Using Internet Explorer (Version 5. 0 or later) Complete connections to external equipment before starting the operation. (See pages 2129 of the projector's operation manual. ) Complete the AC cord connection. (See page 30 of the projector's operation manual. ) Note · When connecting the projector to the LAN, use a LAN cable (Category 5). When connecting the projector to a hub, use a straight-through cable. 1 2 Start Internet Explorer (version 5. 0 or later) on the computer. Enter "http://" followed by the projector IP address set by the procedure on page 23 followed by "/" in "Address", and then press the "Enter" key. · When "DHCP Client" is set to "OFF" on the projector, IP address is 192. 168. 150. 2. Setting the TCP port number used when exchanging data with the projector (from 1025 to 65535). Setting the port number used when searching for the projector (from 1025 to 65535). Items SMTP Server Setting example / Remarks Setting an SMTP server address for e-mail transmission. e. g. 1 : 192. 168. 150. 253 e. g. 2 : smtp123. sharp. co. jp * When using a domain name, make settings for the DNS server. Setting the projector's e-mail address. The e-mail address set here becomes Originator E-mail Address. The name set here appears in the "Originator Name" column of the body of the message. Originator E-mail Address Originator Name Data Port Search Port Note · SMTP Server, Originator E-mail Address and Originator Name can be up to 64 characters. · You can input the characters below: SMTP Server and Originator E-mail Address : a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |, }, ~, _, ', . , @, ` (You can input "@" only one time for "Originator E-mail Address". ) Originator Name : a-z, A-Z, 0-9, -, _, (, ), space · If the settings of "3. Setting up a Network Connection for the Projector" on pages 22 and 23 are incorrectly set, e-mail will not be send. After clicking the "Apply" button, the set values appear. Confirm that the values are set properly, and then click the "Confirm" button. Note · After setting items, wait for 10 seconds and then re-access. · Projector Name can be up to 12 characters. [. . . ] · The IP address parts shown by the subnet mask for the projector and the computer should be the same. (Example) When the IP address is "192. 168. 150. 2" and the subnet mask is "255. 255. 255. 0" for the projector, the IP address for the computer should be "192. 168. 150. X" (X=3-254) and the subnet mask should be "255. 255. 255. 0". · Gateway When the gateway setting for the projector is "0. 0. 0. 0" (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: · The subnets for the projector and the computer should be the same. · The IP address parts shown by the subnet mask for the projector and the computer should be the same. [. . . ]