User manual SHARP XL-HF201PHBK

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. [. . . ] To cancel the programmed play mode: While in the stop mode and the "MEMORY" indicator is lit, press the CLEAR/DIMMER button on the remote control. The "MEMORY" indicator will disappear and all the programmed contents will be cleared. Adding tracks to the program: If a program has been previously stored, the "MEMORY" indicator will be displayed. The new tracks will be stored after the last track of the original program. To check which tracks are programmed: While the unit is stopped in the programmed play mode, press the or button. Notes: " When a disc with programmed tracks is ejected, the program is automatically canceled. " Even if you press the ON/STAND-BY button to enter the stand-by mode or change the function from CD to another, the programmed selections will not be cleared. " During the program operation, random play is not possible. " During programmed play, the CD DIRECT PLAY button will not work. 2 CD Playback Press one of the 1 - 5 buttons to select the desired disc. Selected disc number 3 Press the direct search buttons on the remote control to select the desired track. Selected track number You can also select a track by pressing the or button. 4 5 Press the MEMORY/SET (MEMORY) button to save the track number. If you make a mistake, the programmed tracks can be cleared by pressing the CLEAR/DIMMER button. Store the stations in memory, in order, starting with preset channel 1. Within 30 seconds, press the MEMORY/SET (MEMORY) button to store that station in memory. 4 If the "MEMORY" and preset number indicators go out before the station is memorized, repeat the operation from step 2. 5 Repeat steps 1 - 4 to set other stations, or to change a preset station. When a new station is stored in memory, the station previously memorized will be erased. !To erase entire preset memory 1 2 Press the ON/STAND-BY button to enter the stand-by mode. While pressing down the button and the X-BASS/DEMO button, press the CLOCK/TIMER button until "TUNER CL" appears. Note: The backup function protects the memorized stations for a few hours should there be a power failure or the AC power cord disconnection. 22 Listening to a cassette tape Before playback: " For playback, use normal or low-noise tapes for the best sound. (Metal or CrO tapes are not recommended. ) " Do not use C-120 tapes or poor-quality tapes, as they may cause malfunctions. " Before loading a tape into the cassette compartment, tighten the slack with a pen or a pencil. XL-HF201PHBK !Tape playback 1 2 3 Press the ON/STAND-BY button to turn the power on. Open the cassette door by pushing the area marked " PUSH EJECT". 4 Load a cassette into the cassette compartment with side A facing you. 5 Press the button to choose one side or both sides. To play both sides ( ), start from side A. When playback starts from side B, side A will not be played. [. . . ] There may be some deviations from these values in individual units. XL-HF201PHBK !Tuner Frequency range FM: 87. 5 - 108 MHz AM: 530 - 1, 720 kHz !General Power source Power consumption Dimensions AC 120 V, 60 Hz 92 W Width: 7-1/4" (185 mm) Height: 10-1/4" (260 mm) Depth: 12" (307 mm) 14. 5 lbs. Cassette deck Frequency response Signal/noise ratio Wow and flutter 50 - 14, 000 Hz (normal tape) 50 dB (recording/playback) 0. 3 % (WRMS) Weight ! [. . . ]