User manual SHARP XL-HF300PH

[. . . ] HI FI-KOMPONENTEN-SYSTEM SYSTME HI FI SISTEMA HI FI COMPONENTE HI FI KOMPONENT SYSTEM HI FI SISTEMI HI FI SYSTEEM SISTEMA DE COMPONENTE HI FI HI FI-KOMPONENTTIJRJESTELM HI FI COMPONENT SYSTEM BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUAL DE MANEJO BRUKSANVISNING MANUALE DI ISTRUZIONI MODELL MODLE MODELO MODELL MODELLO MODEL MODELO MALLI MODEL XL-HF300PH(S) GEBRUIKSAANWIJZING MANUAL DE OPERAO KYTTOHJE OPERATION MANUAL iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc. , registered in the U. S. and other countries. DEUTSCH FRANAIS ESPAOL SVENSKA ITALIANO NEDERLANDS PORTUGUS SUOMI ENGLISH Siehe Seiten i bis viii und D-1 bis D-22. Se reporter aux pages i viii et F-1 F-22. Consulte las pginas i a viii y S-1 a S-22. [. . . ] You may be injured. The first time the unit is plugged in, the unit will enter the demonstration mode. To cancel the demonstration mode, press the DEMO/ DIMMER button (remote control) during power standby mode. The unit will enter the low power consumption mode. To return to the demonstration mode, press the DEMO/ DIMMER button again. Connecting iPod or iPhone to TV Speaker connection Photo and video files from iPod or iPhone can be viewed by connecting the system to TV/monitor. If the TV/monitor has a video input, connect it to the VIDEO OUT socket at the back of the unit and set the TV Out on the iPod or iPhone unit to "ON" position. Note: Please make sure to set iPod unit to either NTSC or PAL to match your TV signal. Please visit Apple's homepage for further information. AC power connection After checking all the connections have been made correctly, plug the AC power lead of this unit into the wall socket. Note: Unplug the AC power lead from the wall socket if the unit will not be in use for a prolonged period of time. E-4 System connections (continued) Using other subwoofer Remote control Battery installation You can connect a subwoofer with an amplifier to the SUBWOOFER PRE OUT socket. Audio cable (commercially available) Commercially available subwoofer (amplifier built in) Audio signal To audio input socket Main unit To SUBWOOFER PRE OUT socket 1 Open the battery cover. 2 Insert the supplied batteries according to the direction indicated in the battery compartment. When inserting or removing the batteries, push them towards the () battery terminals. 3 Close the cover. Notes: No sound is heard from the subwoofer without a built-in amplifier. Subwoofer Pre-out (audio signal): 200mV / 10k ohms at 70 Hz. Connecting a TV, etc. To audio output sockets Connect to the TV using an audio cable. TV Audio cable (commercially available) Audio signal To LINE input sockets Caution: Replace all old batteries with new ones at the same time. Remove the batteries if the unit will not be used for a long period of time. This will prevent potential damage due to battery leakage. Do not use rechargeable batteries (nickel-cadmium battery, etc. ). Installing the batteries incorrectly may cause the unit to malfunction. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. Notes concerning use: Replace the batteries if the operating distance is reduced or if the operation becomes erratic. Purchase 2 "AAA" size batteries (UM/SUM-4, R3, HP-16 or similar). Periodically clean the transmitter on the remote control and the sensor on the unit with a soft cloth. [. . . ] No image appears on the TV/monitor. Before transporting the unit Remove the iPod, USB memory device and disc from the unit. Then, set the unit to the power stand-by mode. Carrying the unit with iPod or USB memory device left docked or discs left inside might damage the unit. iPod or iPhone will not charge. Care of compact discs "This accessory is not made to work with iPhone" or similar, appears on iPhone screen. Condensation Sudden temperature changes, storage or operation in an extremely humid environment may cause condensation inside the cabinet (CD pickup, etc. ) or on the transmitter on the remote control. Condensation can cause the unit to malfunction. [. . . ]