User manual SHARP XL-HP404H

[. . . ] MIKRO KOMPONENTEN SYSTEM MICRO-CHANE SISTEMA MICRO MIKRO KOMPONENT SYSTEM MICRO SISTEMI MICRO SYSTEEM SISTEMA DE MICRO COMPONENTE MICRO COMPONENT SYSTEM MODELL MODLE MODELO MODELL MODELLO MODEL MODELO MODEL Mikro Komponenten System XL-HP404H besteht aus XL-HP404H (Hauptgert) und CP-HP404H (Lautsprechersystem). Micro-chane XL-HP404H compose de XL-HP404H (appareil principal) et CPHP404H (enceinte acoustique). Sistema micro XL-HP404H que consta de XL-HP404H (aparato principal) y CPHP404H (sistema de altavoces). XL-HP404H mikro komponent system bestende av XL-HP404H (huvudenhet) och CP-HP404H (hgtalarsystem). [. . . ] " In random play, the CD player will select and play tracks automatically. (You cannot select the order of the tracks. ) Caution: After performing repeat or random play, be sure to press the ) button. Otherwise, the disc(s) will play continuously. (CD CD Playback To cancel random play: Press the / button. "R" will go out. 8 E-16 03/10/30 XL-HP404H(H)E2. fm TINSZA004AWZZ XL-HP404H Advanced CD Playback (continued) !Programmed play You can choose up to 32 selections for playback in the order you like. ENGLISH 1 Whilst in the stop mode, press the MEMORY/SET (MEMORY) button to enter the programming save mode. To clear the programmed selections: Press the CLEAR/DIMMER button on the remote control whilst the "MEMORY" indicator is flashing. Each time the button is pressed, one track will be cleared, beginning with the last track programmed. To cancel the programmed play mode: Whilst in the stop mode and the "MEMORY" indicator is lit, press the CLEAR/DIMMER button on the remote control. The "MEMORY" indicator will disappear and all the programmed contents will be cleared. Adding tracks to the programme: If a programme has been previously stored, the "MEMORY" indicator will be displayed. The new tracks will be stored after the last track of the original programme. 18 2 Press one of the 1 - 5 buttons to select the desired disc. CD Playback Selected disc number 3 Press the direct search buttons on the remote control to select the desired track. Selected track number You can also select a track by pressing the or button. To check which tracks are programmed: Whilst the unit is stopped in the programmed play mode, press the or button. Notes: " When a disc with programmed tracks is ejected, the programme is automatically cancelled. " Even if you press the ON/STAND-BY button to enter the stand-by mode or change the function from CD to another, the programmed selections will not be cleared. " During the programme operation, random play is not possible. " During programme play, the CD DIRECT PLAY button will not work. 4 5 Press the MEMORY/SET (MEMORY) button to save the track number. If you make a mistake, the programmed tracks can be cleared by pressing the CLEAR/DIMMER button. Press the / button to start playback. SHARP TINSZA004AWZZ (H) 6 7 E-17 03/10/30 XL-HP404H(H)E2. fm TINSZA004AWZZ Listening to the radio 3 Press the TUNING ( station. or ) button to tune in to the desired XL-HP404H ENGLISH Manual tuning: Press the TUNING button as many times as required to tune in to the desired station. Auto tuning: When the TUNING button is pressed for more than 0. 5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station. Notes: " When radio interference occurs, auto scan tuning may stop automatically at that point. " Auto scan tuning will skip weak signal stations. [. . . ] " Do not write on either side of the disc, particularly the non-label side from which signals are read. " Keep your discs away from direct sunlight, heat, and excessive moisture. " Always hold the CDs by the edges. Fingerprints, dirt, or water on the CDs can cause noise or mistracking. [. . . ]