User manual SHARP XL-UH2000H

[. . . ] MIKRO KOMPONENTEN SYSTEM MICRO-CHANE SISTEMA MICRO MIKRO KOMPONENT SYSTEM MICRO SISTEMI MICRO SYSTEEM SISTEMA DE MICRO COMPONENTE MICRO COMPONENT SYSTEM MODELL MODLE MODELO MODELL MODELLO MODEL MODELO MODEL Mikro Komponenten System XL-UH2000H besteht aus XL-UH2000H (Hauptgert) und CP-UH2000H (Lautsprechersystem). Micro-chane XL-UH2000H compose de XL-UH2000H (appareil principal) et CP-UH2000H (enceinte acoustique). Sistema micro XL-UH2000H que consta de XL-UH2000H (aparato principal) y CP-UH2000H (sistema de altavoces). XL-UH2000H mikro komponent system bestende av XL-UH2000H (huvudenhet) och CP-UH2000H (hgtalarsystem). [. . . ] To confirm the time display: [When the unit is in the stand-by mode] Press the CLOCK/TIMER button. The time display will appear for about 10 seconds. [When the power is on] Press the CLOCK/TIMER button. Within 10 seconds, press the or button to display the time. The time display will appear for about 10 seconds. Note: The "CLOCK" will appear or time will flash to confirm the time display when the AC power supply is restored after a power failure or unplugging the unit. If incorrect, readjust the clock as follows. To readjust the clock: Perform "Setting the clock" from step 1. If the "CLOCK" does not appear in step 3, step 4 (for selecting the 24-hour or 12-hour display) will be skipped. To change the 24-hour or 12-hour display: 1 Clear all the programmed contents. [Refer to "Factory Reset, Clearing All Memory" on page 36 for details. ] 2 Perform "Setting the clock" from step 1. 1 2 3 Press the ON/STAND-BY button to turn the power on. Within 10 seconds, press the or button to select "CLOCK", and press the MEMORY button. 4 Press the or button to select 24-hour or 12-hour display and then press the MEMORY button. "0:00" "AM 12:00" "AM 0:00" The 24-hour display will appear. (0:00 - 23:59) The 12-hour display will appear. (AM 12:00 - PM 11:59) The 12-hour display will appear. (AM 0:00 - PM 11:59) E-11 Listening to a CD or MP3/WMA disc This system can play back a standard CD, CD-R/RW in the CD format and CD-R/RW with MP3 or WMA files, but cannot record on them. Some audio CD-R and CD-RW discs may not be playable due to the state of the disc or the device that was used for recording. It is an acronym which stands for MPEG Audio Layer 3. MP3 is a type of audio code which is processed by significant compression from the original audio source with very little loss in sound quality. This system supports MPEG 1 Layer 3, MPEG 2 Layer 3, and VBR files. During VBR file playback, time counter in the display may differ from its actual playback time. Bitrate which is supported by MP3 is 32 ~ 320 kbps. WMA: WMA files are Advanced System Format files that include audio files which are compressed with Windows Media Audio codec. [. . . ] 2 ON/ STAND-BY Condensation Sudden temperature changes, storage or operation in an extremely humid environment may cause condensation inside the cabinet (CD pickup, etc. ) or on the transmitter on the remote control. Condensation can cause the unit to malfunction. If this happens, leave the power on with no disc in the unit until normal playback is possible (about 1 hour). Wipe off any condensation on the transmitter with a soft cloth before operating the unit. Caution: This operation will erase all data stored in memory including clock, timer settings, tuner preset, and CD programme. E-36 References Tuner 1 Press the ON/STAND-BY button to enter the power stand-by mode. [. . . ]