User manual SHARP XL1100 OPERATION MANUAL

[. . . ] COMPACT AUDIO SYSTEM MODEL Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. XL-1000H Compact Audio System consisting of XL-1000H (main unit) and CP-XL1000H (speaker system). [. . . ] Within 5 seconds, press the VOLUME ( or ) button to adjust the bass. Remote control operation: - Sound Control - Press the BASS ( or ) button to adjust the bass. -5 . . . 0 . . . 5 , , Adjusting the treble Main unit operation: 1 2 Press the BASS/TREBLE button until "TRE" appears on the display. Within 5 seconds, press the VOLUME ( or ) button to adjust the treble. Remote control operation: Press the TREBLE ( or ) button to adjust the treble. -5 . . . 0 . . . 5 14 Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) 01/1/17 XL-1000H(E)2. fm Setting the Clock 3 Within 1 minute, press the PRESET ( or hour and then press the MEMORY button. ) button to adjust the z When the 12-hour display is selected, "AM" will change automatically to "PM". 4 Within 1 minute, press the PRESET ( or ) button to adjust the minutes and then press the MEMORY button. To confirm the time display when the power is on: This may be operated only with the remote control. In this example, the clock is set for the 24-hour (0:00) display. The time display will appear for about 5 seconds. 1 Press the CLOCK button and within 3 seconds, press the MEMORY button. Note: The time will flash at the push of the CLOCK button when the AC power supply is restored after a power failure or unplugging the unit. Readjust the clock as follows. To readjust the clock: 2 Within 1 minute, press the PRESET ( or ) button to select 24hour or 12-hour display and then press the MEMORY button. Perform "Setting the Clock" from the beginning. To change the 24-hour or 12-hour display: 1 2 Clear all the programmed contents. [Perform to step 3 under "If trouble occurs" on page 26 for details. ] Perform "Setting the Clock" from the beginning. "0:00" The 24-hour display will appear. (0:00 - 23:59) "AM 12:00" The 12-hour display will appear. (AM 12:00 - PM 11:59) Note that this can only be set when the unit is first installed or it has been reset. (Refer to step 3 under "If trouble occurs" on page 26. ) Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) 15 01/1/17 XL-1000H(E)2. fm - Setting the Clock - z The hour will not advance even if minutes advance from "59" to "00". z The clock starts from "0" second. (Seconds are not displayed. ) Basic Operation Listening to a CD 1 2 3 4 Press the ON/STAND-BY button to turn the power on. Press the FUNCTION button until "CD STOP" or "NO DISC" appears on the display. When operating with the remote control, press the CD button. Press the (OPEN/CLOSE) button to open the CD compartment. Place a CD on the spindle, label side up. Be sure to place 8 cm (3") disc in the middle of a disc holder. 12 cm (5") 8 cm (3") CD Playback - Listening to a CD - 5 Press the (OPEN/ CLOSE) button to close the CD compartment. Total number of tracks Total playing time 6 Press the ( ) button to start playback from track 1. When the last track on the disc has finished playing, the CD player will stop automatically. To interrupt playback: Main unit operation: Press the button. To resume playback from the same point, press the Remote control operation: Press the button. To resume playback from the same point, press the button again. button. To stop playback: Press the button. 16 Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) 01/1/17 XL-1000H(E)2. fm To remove the CD: Whilst in the stop mode, press the (OPEN/CLOSE) button. Press the CD eject button and remove the CD. , , To locate the beginning of a track To move to the beginning of the next track: Press the button for less than 0. 5 seconds during playback. z You can skip to any track by pressing the button repeatedly until the desired track number appears. To restart the track being played: Press the button for less than 0. 5 seconds during playback. z You can skip to any track by pressing the button repeatedly until the desired track number appears. CD Playback CD Eject Button Notes: z After removing the CD, make sure to press the (OPEN/CLOSE) button and close the CD compartment. z When the unit enters the stand-by mode, the opened CD compartment cover will be closed automatically. , , To locate the desired portion For audible fast forward: Press and hold down the button during playback. After use: Press the ON/STAND-BY button to enter the power stand-by mode. Caution: For audible fast reverse: Press and hold down the button during playback. z Do not stop or move the CD compartment cover manually. z Be careful not to jam your fingers in the CD compartment cover. z If the power fails whilst the compartment is open, wait until the power is restored. [. . . ] z Has condensation formed inside the unit? Web-site: www. sharp. co. uk/support Help Line: 08705 274277 (office hours) 25 01/02/19 XL-1000H(E)3. fm - Troubleshooting Chart - References z The remote control does not oper- z Is the AC power lead of the unit plugged ate. in? Troubleshooting Chart (continued) , , If trouble occurs When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc. ) or if it is operated incorrectly, it may malfunction. If such a problem occurs, do the following: 1 Set the unit to the stand-by mode and turn the power on again. 2 If the unit is not restored in step 1, unplug and plug in the unit, and then turn the power on. [. . . ]