User manual SHARP XL570E OPERATION MANUAL

[. . . ] MICRO COMPONENT SYSTEM OPERATION MANUAL MODEL XL-570E XL-560E XL-570E micro component system consisting of XL-570E micro component system and CPXL570H speaker system. XL-560E micro component system consisting of XL-560E micro component system and CPXL560H speaker system. CONTENTS Page SPECIAL NOTES . . Back cover SPECIAL NOTES NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a nonrewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. Always refit the fuse cover after replacing the fuse. [. . . ] q If the beginning of the disc is reached whilst reviewing, the mode will automatically switch to normal playback at that point. 9 XL-560E/XL-570E(SUK) TINSE0019SJZZ (Continued) 1 6 s APMS (Automatic Programmable Music Selector) q The CD can be programmed to play the tracks in any order, or skip certain tracks. 2, 4 3 1 2 3 Load a compact disc and close the CD compartment. Press the MEMORY/SET (MEMORY) button to prepare for programming. Within 30 seconds, turn the jog dial on the main unit or press the 3 / 5 or 2 / 4 button on the remote control to select the desired track. Press the MEMORY/SET (MEMORY) button. q "MEMORY" will flash. CLEAR 2, 4 6 3 4 q The selected track number and the programmed playback order will be displayed. q After 2 seconds, the total playing time of the programmed tracks will be displayed automatically. 5 Selected track number Playback order Repeat steps 3 - 4 for any other track Up to 20 tracks can be programmed. ming mode (when MEMORY is flashing) or if you change your mind, the programmed tracks can be cleared by pressing the CLEAR button on the remote control. The tracks will be cleared sequentially starting with the last entered track. q If you make a mistake whilst in the program- 6 Total playing time Caution: q Do not open the CD compartment during playback (or whilst paused). q If the disc is damaged, dirty, or loaded upside down, "NO DISC" or "READ ERR" will appear in the display. Clean, replace, or reload the disc properly. q Keep foreign objects out of the CD compartment. q Subjecting the unit to shock or vibration may cause mistracking. q When the unit is not being used, be sure to close the CD compartment. If it is left open, the lens may become covered with dust and the unit may not operate properly. q Playing certain compact discs at a high volume may cause mistracking. q If TV or radio interference occurs during CD operation, move the unit away from the TV or radio. Press the 0 / CD 6 (0 6) button to start playback of programmed selections. To clear all the programmed selections: To cancel a programmed sequence, press the CLEAR button on the remote control whilst the disc is stopped and the "MEMORY" indicator is lit. Notes: q Opening the CD compartment automatically cancels the programmed sequence. q Even if you press the ON/STAND-BY button to enter the stand-by mode or the function is changed from CD to some other function, the programmed selections will not be cleared. q Programming is not possible during CD playback. It must be performed whilst the CD is stopped. q When in the random play mode (whilst "RANDOM" is lit), programming is not possible. To perform some programming, cancel the random play mode. 10 XL-560E/XL-570E(SUK) TINSE0019SJZZ CASSETTE OPERATION s Cassette tape q For playback, use normal or low-noise tape for the best sound. (Metal or CrO2 tape is not recommended. ) For recording, use only normal tape. [. . . ] Unplug the AC power lead from the AC INPUT socket on this unit. Whilst pressing down the MEMORY/SET button and the BASS/TREBLE button, plug the AC power lead into the AC INPUT socket on this unit. Note: q Only CD signals can be output. Caution: q The operation explained above will erase all data stored in memory, such as clock and timer settings, and tuner and CD presets. 17 XL-560E/XL-570E(SUK) TINSE0019SJZZ MAINTENANCE q Amplifier section Output power: Output terminals: Input terminals: RMS; 40 W (20 W + 20 W) (10 % T. H. D. ) Speakers; 4 ohms Headphones; 16-50 ohms (recommended; 32 ohms) Video/Auxiliary (audio signal); 500 mV/47 kohms FM; 87. 5-108 MHz AM; 522-1, 620 kHz Compact disc player Non-contact, 3-beam semiconductor laser pickup 1-bit D/A converter 8-times oversampling digital filter 20 - 20, 000 Hz Unmeasurable (less than 0. 001% W. peak) 50 - 14, 000 Hz (Normal tape) 50 dB 0. 25 % (WRMS) q Tuner section s Internal care q Do not touch the Laser pickup lens. If fingerprints or dust accumulate on the pickup, clean it gently with a dry cotton swab. [. . . ]