User manual SHARP XL70 OPERATION MANUAL

[. . . ] MODEL MICRO COMPONENT SYSTEM OPERATION MANUAL XL-60H XL-70H Thank you for purchasing this SHARP product. To obtain the best performance from this product please read this manual carefully. It will guide you in operating your SHARP product. XL-60H/XL-70H Micro Component System consisting of XL-60H/XL-70H (main unit) and CP-XL60H/ CP-XL70H (speaker system). XL-60H XL-70H 60H/70H(SUK). FRONT 1 00. 1. 7, 5:07 PM SPECIAL NOTES NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a nonrewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. [. . . ] q Before changing from one tape operation to another, press the s button. q If a power failure occurs during tape operation, the tape head will remain engaged with the tape and the cassette door will not open. In this case, wait until power is restored. q Even if the 0 / CD 6 button is pressed during tape playback, the unit will not enter the pause mode. The pause mode is only active during synchronised operation of the cassette deck and CD. In the normal cassette mode, use the s button. 5 1 2 16 60H/70H(SUK)13-17 16 00. 1. 5, 11:40 AM RADIO OPERATION s Tuning s Preset tuning You can store up to 30 stations in memory (30 stations consisting of any combination of FM and AM stations you like) and recall them. 1 3, 5, 6 2 4 1 Press the ON/STAND-BY button to turn the power on. 2, 4 To enter stations into memory: 3 2 Press the FUNCTION button until "FM" or "AM" appears in the display. 3 Press the BAND button to select the desired fre- 1 Perform steps 1 - 6 in the "Tuning" section. (FM ST, FM or AM) 2 Press the MEMORY/SET button. 4 Press the TUNING (X or W) button to tune in to q "MEMORY" will flash. 3 Within 5 seconds, turn the jog dial to make the Manual tuning: Press the TUNING (X or W) button as many times as required to adjust the frequency shown on the display to the frequency of the desired station. preset channel number flash in the display. q Store the stations in memory, in order, starting with preset channel 1. button to store that station in the selected station preset number memory. q If the "MEMORY" and preset number indicators go out before the station is memorised, repeat the operation from step 2. Auto tuning: When the TUNING (X or W) button is pressed for more than 0. 5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station. Notes: q When radio interference occurs during auto scan tuning, auto scan tuning may stop automatically at that point. q If a weak station signal is found during auto scan tuning, the station will be skipped. q To stop the auto tuning, press the TUNING (X or W) button again. q When an RDS (Radio Data System) station is tuned in, the frequency will be displayed first and then the RDS indicator will light. Finally, the station name will appear. 4 Within 5 seconds, press the MEMORY/SET 5 Repeat steps 1 - 4 to set other preset stations, or to change a preset station. After use: Press the ON/STAND-BY button to enter the standby mode. 5 To receive an FM stereo transmission, press the BAND button so that the "ST" indicator on the display lights up. q "j" will appear when an FM broadcast is in stereo. button so that the "ST" indicator goes out. q The reception changes to monaural, the sound becomes clearer. Note: q The last station tuned in will be recalled, even after changing the tuning band or the function, or after switching the unit to the stand-by mode. 6 If the FM reception is weak, press the BAND 17 60H/70H(SUK)13-17 17 00. 1. 5, 11:40 AM (Continued) To recall a memorised station: To clear a memorised station: 2 1 PRESET ( ) 3 4 2 1 1 Press the VOLUME/JOG button. [. . . ] q If the operation is not correct. 1 Press the ON/STAND-BY button to enter the stand-by mode. 2 Unplug the AC power lead from the AC INPUT socket on this unit. AC INPUT 3 Whilst pressing down the MEMORY/SET button and the 0 button, plug the AC power lead into the AC INPUT socket on this unit. Caution: q The operation explained above will erase all data stored in memory, such as clock and timer settings, and tuner and CD presets. 2, 3 MAINTENANCE q After long use, the deck's heads and capstan may become magnetised, causing poor sound. Demagnetise these parts once every 30 hours of playing/recording time by using a commercial tape head demagnetiser. Read the demagnetiser's instructions carefully before use. s Internal care q Do not touch the laser pickup lens. [. . . ]