User manual SHARP XR-1S

[. . . ] Introduction Quick Start Setup Connections Basic Operation Useful Features Appendix MULTIMEDIA PROJECTOR XR-1S MODEL OPERATION MANUAL IMPORTANT For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 11. Model No. : XR-1S Serial No. : SPECIAL NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 5A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 and of the same rating as above, which is also indicated on the pin fuse marked or face of the plug, must be used. [. . . ] · If the projector is put into the standby mode and immediately turned on again, the lamp may take some time to start projection. ON/STANDBY button On-screen Display (confirmation message) Turning the Power off (Putting the Projector into Standby Mode) 1 Press SON/STANDBY on the projector or AON/STANDBY on the remote control, then press that button again while the confirmation message is displayed, to put the projector into standby mode. Unplug the power cord from the AC outlet after the cooling fan stops. · When the projector is turned off, the Adjustment buttons blink in a counterclockwise direction. (When "Guide LEDs" is set to "On". n page 48) R Info · Do not unplug the power cord during projection or cooling fan operation. This can cause damage due to rise in internal temperature, as the cooling fan also stops. 2 26 Image Projection About the Setup Guide After turning on the projector, the Setup Guide screen appears to assist you with projector setup. Guidance items 1 FOCUS 2 HEIGHT ADJUST 3 ZOOM Setup Guide screen Adjust the projector by following the illuminated buttons or Setup Guide indicators. Press TENTER to turn off the Setup Guide screen. Note · The Setup Guide screen automatically highlights the items in order of 1 FOCUS 2 HEIGHT ADJUST 3 ZOOM 4 ENTER . · You can adjust the focus, height or zoom anytime you want, regardless of the selection on the Setup Guide. · If you do not want to display the Setup Guide for the next time, set "Menu" - "SCR - ADJ" "Setup Guide" to "Off". (See page 45. ) Setup Guide indicator ON/STANDBY button ENTER button Basic Operation Adjusting the Projected Image 1 Adjusting the Focus You can adjust the focus with the focus ring on the projector. Rotate the focus ring to adjust the focus while watching the projected image. Focus ring 27 Image Projection (Continued) 2 Adjusting the Height The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector. When the screen is in a higher position than the projector, the projection image can be made higher by adjusting the projector. HEIGHT ADJUST button 1 2 Lift the projector to adjust its height while pressing the HEIGHT ADJUST button. Remove your hands from the HEIGHT ADJUST button of the projector after its height has been finely adjusted. · The angle of projection is adjustable up to 7. 5 degrees from the surface on which the projector is placed. 3 Use the rear adjustment foot to make the projector level. · The projector is adjustable ±1 degree from the standard position. Note · When adjusting the height of the projector, trapezoidal distortion occurs. When "Auto Keystone" is set to "On", keystone correction functions automatically to correct trapezoidal distortion. When you want to adjust the automatically corrected image, use the manual keystone correction. (See page 44. ) Rear adjustment foot Info · Do not apply too much pressure on the projector when the front adjustment foot comes out. · When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the projector. 3 Adjusting the Screen Size You can adjust the screen size using the zoom knob on the projector. zoom in zoom out Zoom Knob 28 Switching the Input Mode Select the appropriate input mode for the connected equipment. PressC INPUT 1, D INPUT 2 or EINPUT 3 on the remote control to select the input mode. · When pressing INPUT (W/Y) on the projector, input mode switches in order of INPUT1 INPUT2 INPUT3 . · When "Auto Search" is set to "On", INPUT (W/ Y) on the projector functions as the Auto Search buttons. (See page 47. ) INPUT buttons AV MUTE button Volume buttons Adjusting the Volume Press K/L on the remote control or V/X on the projector to adjust the volume. Note · Pressing K/V will lower the volume. · Pressing L/X will raise the volume. On-screen Display Basic Operation Displaying the Black Screen and Turning off the Sound Temporarily Press MAV MUTE on the remote control to temporarily display a black screen and turn off the sound. Note · Pressing MAV MUTE again will turn the projected image back on. On-screen Display 29 Image Projection (Continued) Resize Mode This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose "NORMAL", "BORDER" or "STRETCH" image. Press HRESIZE. · See page 43 for setting on menu screen. RESIZE button Computer NORMAL 4:3 aspect ratio SVGA (800 K 600) XGA (1024 K 768) SXGA (1280 K 960) SXGA L (1400 K 1050) SXGA (1280 K 1024) 1280 K 720 BORDER STRETCH 800 K 600 600 K 450 800 K 450 Other aspect ratios J J 800 K 450 Input Signal Computer Image type Output screen image NORMAL Projects a full screen image while maintaining the aspect ratio. BORDER Projects 4:3 image fully in STRETCH (the following column) image. STRETCH Projects 16:9 image evenly over entire screen (top/bottom blank bands). Resolution lower than SVGA 4:3 aspect ratio SVGA 4:3 aspect ratio Resolution higher than SVGA 4:3 aspect ratio SXGA (1280K1024) 5:4 aspect ratio 1280K720 16:9 aspect ratio 30 * Mode for projecting an image with the original aspect ratio without cutting any portions. : Cutout area on which images cannot be projected. VIDEO · "STRETCH" is fixed when 540P, 720P or 1080I signals are entered. Output screen image Input Signal NORMAL Projects a full screen image. BORDER Projects 4:3 image fully in STRETCH (the following column) image. STRETCH Projects 16:9 image evenly over entire screen (top/bottom black bands). DVD / Video Image type 4:3 aspect ratio 480I, 480P, NTSC, PAL, SECAM Letter box Squeezed 16:9 image Squeezed 4:3 image Basic Operation 16:9 aspect ratio 540P, 720P, 1080I (16:9) 16:9 aspect ratio (4:3 aspect ratio in 16:9 screen) * Mode for projecting an image with the original aspect ratio without cutting any portions. : Cutout area on which images cannot be projected. [. . . ] 33 Rear adjustment foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Remote control sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]