User manual SHARP XR-55S

[. . . ] Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. [. . . ] It should not be regarded as faulty operation. · If the projector is put into Standby mode and immediately turned on again, the lamp may take some time to start projection. · When System Lock is set, the keycode input box appears. To cancel the keycode setting, input the keycode that you have already set. See page 50 for details. STANDBY button ON button Basic Operation On-screen display (confirmation message) Turning the Power Off (Putting the Projector into Standby Mode) Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again while the confirmation message is displayed, to put the projector into Standby mode. · The projector cannot be turned on while cooling. Info · Direct Power Off function: You can unplug the power cord from the AC outlet even if the cooling fan is still running. 25 Image Projection Setup Guide screen About the Setup Guide After turning on the projector, the Setup Guide screen appears to assist you with projector setup. Guidance items 1 FOCUS 2 HEIGHT ADJUST 3 ZOOM Press ENTER to exit the Setup Guide screen. Note · The Setup Guide screen automatically highlights the items in the following order: 1 FOCUS 4 ENTER 2 HEIGHT ADJUST 3 ZOOM ENTER button However, you can adjust the focus or height (angle) regardless of the highlighted item. · If you do not want to display the Setup Guide for the next time, set "Menu" - "SCR - ADJ" "Setup Guide" to "Off". (See page 48. ) Adjusting the Projected Image 1 Adjusting the Focus You can adjust the focus with the focus ring on the projector. Rotate the focus ring to adjust the focus while watching the projected image. · Using the knob on the focus ring will make the adjustments easier. Focus ring 26 2 Adjusting the Height The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector. When the screen is above the projector, the projection image can be made higher by adjusting the projector. 1 Lift the projector to adjust its height while lifting the HEIGHT ADJUST lever. Make small adjustments. HEIGHT ADJUST lever 2 Remove your hands from the HEIGHT ADJUST lever of the projector after its height has been finely adjusted. · The angle of projection is adjustable up to 9 degrees from the surface on which the projector is placed. Rear adjustment foot 3 Use the rear adjustment foot to make the projector level. · The projector is adjustable ±2 degrees from the standard position. Basic Operation Info · Do not apply too much pressure on the projector when the front adjustment foot comes out. · When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the projector. may be an infringement of copyright protected by law for copyright holders. Please use caution. 31 Operating with the Remote Control BREAK TIMER button FREEZE button MAGNIFY buttons POINTER button SPOT button Adjustment buttons (P/R/O/Q) EFFECT button PICTURE MODE button ECO+QUIET button AUTO SYNC button Displaying the Pointer 1 Press POINTER and press P/R/ O/Q on the remote control to move the pointer. · Press EFFECT to change the pointer icon (5 types). Star Finger1 Finger2 Heart Underline 2 Press POINTER again. · The pointer will disappear. Using the Spot Function Displaying and Setting the Break Timer 1 1 Press BREAK TIMER. · The timer starts to count down from 5 minutes. Press SPOT and press P/R/O/Q on the remote control to move the spot area. · Press EFFECT to change the spot area size (3 types). 1/9 1/25 1/8 On-screen display 2 Press P/R/O/Q to adjust the length of the break time. · Increases with P or Q · Shortens with O or R 2 Press SPOT again. · The spot area will disappear. 5 minutes 6 minutes 60 minutes 4 minutes 3 minutes 1 minute · The break time can be set in units of one minute (up to 60 minutes). Switching the Eco+Quiet Mode Press ECO+QUIET to switch the Eco+Quiet mode between on and off. · When the Eco+Quiet Mode is set to "ON", the sound of the cooling fan will turn down, the power consumption will decrease, and the lamp life will extend. Canceling the break timer display function Press BREAK TIMER. Note · The Break Timer is not available while the projector is operating the following functions. - Auto Sync - Freeze - AV Mute - Input Search Note · Refer to "Eco+Quiet" on page 43 for details. 32 Auto Sync (Auto Sync Adjustment) Auto Sync function works when detecting input signal after the projector turns on. Press AUTO SYNC to manually adjust with Auto Sync function. Note · When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page 44. ) Displaying an Enlarged Portion of an Image Graphs, tables and other portions of projected images can be enlarged. This is helpful when providing more detailed explanations. 1 Press MAGNIFY on the remote control. · Enlarges the image. · Pressing or MAGNIFY enlarges or reduces the projected image. Note Press . ×3 ×4 Freezing a Moving Image ×1 ×2 Press . 1 2 Press FREEZE. · The projected image is frozen. · You can change the location of the enlarged image using P, R, O and Q. Press FREEZE again to return to the moving image from the currently connected device. 2 Press RETURN on the remote control to cancel the operation. · The magnification then returns to ×1. Note Selecting the Picture Mode You can select the appropriate Picture mode for the projected image, such as movie or video game. Press PICTURE MODE. · When pressing PICTURE MODE, the Picture mode changes in the following order: STANDARD PRESENTATION MOVIE GAME sRGB* · The selectable magnifications differ depending on the input signal. · In the following cases, the image will return to the normal size (×1). - When the input signal resolution and refresh rate (vertical frequency) change. [. . . ] · The batteries may be depleted or inserted incorrectly. Make sure the batteries are inserted correctly or insert new ones. · Cables are incorrectly connected to the projector or the connected equipment works improperly. · If this happens frequently, replace the lamp. [. . . ]