User manual SHARP XV-Z2000

[. . . ] XV-Z2000 PROJECTOR PROJEKTOR PROJECTEUR PROJEKTOR PROYECTOR PROIETTORE PROJECTOR OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI BRUKSANVISNING MANUAL DE MANEJO MANUALE DI ISTRUZIONI GEBRUIKSAANWIJZING ENGLISH DEUTSCH FRANÇAIS SVENSKA ESPAÑOL ITALIANO NEDERLANDS SPECIAL NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug, must be used. Always refit the fuse cover after replacing the fuse. [. . . ] INPUT 1, 2, 3, 4, 5 and DIGITAL INPUT button Press , , , , or on the remote control to select the input mode. on the projector, input mode · When pressing switches in order of : INPUT 1 INPUT 2 INPUT 3 INPUT 5 INPUT 4 DIGITAL "On-screen Display of INPUT Mode (Example) INPUT 1 mode Using Component INPUT 2 mode Using Component INPUT 3 mode Using S-Video Note · When no signal is received, "NO SIGNAL" will be displayed. When a signal that the projector is not preset to receive is received, "NOT REG. " will be displayed. · The INPUT mode is not displayed when "OSD Display" of the "Options" menu is set to " (OFF)". (See page 47. ) About the INPUT mode Used for projecting images INPUT 1 (Component) from equipment connected to INPUT 1 terminals. Used for projecting images INPUT 2 (Component) from equipment connected to INPUT 2 terminal. Used for projecting images INPUT 3 from equipment connected (S-Video) to INPUT 3 terminal. Used for projecting images INPUT 4 from equipment connected (Video) to INPUT 4 terminal. Used for projecting INPUT 5 (Component/ images from equipment connected to INPUT 5 RGB) terminal. Used for projecting DIGITAL images from equipment with DVI or RGB output terminal connected to INPUT 5 terminal. INPUT 4 mode Using Video Basic Operation INPUT 5 mode Component RGB · When switching the component and RGB on the remote input mode, press control or select "Signal Type" in the "Options" menu. DIGITAL mode -29 Image Projection Adjusting the Focus 1 2 Press on the remote control. Press \ or | on the remote control to adjust the focus. Note Adjustment buttons ('/"/\/|) ZOOM/FOCUS button · You can also adjust the focus by using and \ or | on the projector. Adjusting the Projected Image Size 1 2 ZOOM/FOCUS button Adjustment buttons ('/"/\/|) Press on the remote control. Press ' or " on the remote control to adjust the zoom. Note · You can also adjust the zoom by using and ' or " on the projector. -30 Using the Adjustment Feet The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector when the screen is located higher than the projector, the screen is inclined or when the installation site is slightly inclined. Install the projector so that it is as perpen- Lens centre dicular to the screen as possible. Side View Top View 1 Lift the projector to adjust its height while pressing the HEIGHT ADJUST button. · The projector is adjustable up to approximately 12 degrees (6 steps). · When lowering the projector, it may be difficult to move the front adjustment foot because the installation surface is difficult to slide. In this case, pull the projector back slightly and adjust its height. 2 Remove your hands from the HEIGHT ADJUST button of the projector after its height has been finely adjusted. Finely adjust the height and inclination by turning the rear adjustment feet. Note Front adjustment foot HEIGHT ADJUST button 3 Basic Operation · When adjusting the projected image position, trapezoidal distortion occurs. In this case, see "Keystone Correction" on page 32. Info · Do not press the HEIGHT ADJUST button when the front adjustment foot comes out without firmly holding the projector. · Do not hold the lens when lifting or lowering the projector. · When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the projector. Rear adjustment feet -31 Image Projection Keystone Correction This function can be used to adjust the Keystone settings. KEYSTONE button Note · When the image is projected from a direction at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. UNDO button Adjustment buttons ('/"/\/|) 1 2 Press on the remote control to enter the Keystone Correction mode. Press '/" to select "H Keystone" or "V Keystone". Selectable items Description "On-screen Display (Keystone Correction mode) H Keystone Horizontally adjusts the keystone settings. V Keystone Vertically adjusts the keystone settings. Returns to the factory preset Reset settings. Horizontal Keystone Correction 3 Press \/| to move the mark on the selected adjustment item to the desired setting. Note · Straight lines and the edges of the displayed image may appear jagged, when adjusting the Keystone setting. · When adjusting "H Keystone" and "V Keystone" at the same time, the values of adjustable angles for each setting become smaller. · The adjustable value of the "V Keystone" becomes extremely small when "H Keystone" is made to be the maximum value. [. . . ] 45 Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 T H HEIGHT ADJUST button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 H-Pos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]