User manual SHARP XV-Z3000

[. . . ] XV-Z3000 PROJECTOR PROJEKTOR PROJECTEUR PROJEKTOR PROYECTOR PROIETTORE PROJECTOR OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI BRUKSANVISNING MANUAL DE MANEJO MANUALE DI ISTRUZIONI GEBRUIKSAANWIJZING ENGLISH DEUTSCH FRANÇAIS SVENSKA ESPAÑOL ITALIANO NEDERLANDS SPECIAL NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 and of the same rating as above, which is also indicated on the pin fuse marked or face of the plug, must be used. Always refit the fuse cover after replacing the fuse. [. . . ] Then select RESET. R On-screen display H&V KEYSTONE END ENTER ADJUST RESET 3 Press P or R on the remote control to align the left and right sides of the projected image. Vertical Keystone Correction (Adjustment with P / R) 4 Press O or Q on the remote control to align the upper and lower sides of the projected image. Horizontal Keystone Correction (Adjustment with O / Q) Basic Operation 5 Press c KEYSTONE or i ENTER on the remote control and the "H&V KEYSTONE" mode ends. Note · If adjustments are made using both "H KEYSTONE" and "V KEYSTONE" at the same time, the image aspect ratio may become slightly distorted. · When adjusting "H KEYSTONE" and "V KEYSTONE" at the same time, the values of adjustable angles for each setting become smaller. · The adjustable value of the "V KEYSTONE" becomes extremely small when "H KEYSTONE" is made to be the maximum value. 35 Image Projection (Continued) Resize Mode This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose "STRETCH", "SIDE BAR", "CINEMA ZOOM" or "DOT BY DOT (Computer input only)" image. Press m RESIZE on the projector or jRESIZE on the remote control. On the projector On the remote control RESIZE button VIDEO RESIZE button · "STRETCH" is fixed when 540P, 720P or 1080I signals are entered. Input Signal DVD / Video Image type STRETCH Output screen image SIDE BAR CINEMA ZOOM 4:3 aspect ratio 480I, 480P, 576I, 576P, NTSC, PAL, SECAM Letter box Squeezed 16:9 aspect ratio 540P, 720P, 1080I 16:9 aspect ratio : Cutout area on which images cannot be projected. 36 Computer Input Signal Computer Image type STRETCH Output screen image SIDE BAR CINEMA ZOOM DOT BY DOT Resolution lower than XGA 4:3 aspect ratio XGA (1024K768) 4:3 aspect ratio 1280K720 16:9 aspect ratio : Cutout area on which images cannot be projected. Note · You can select "CINEMA ZOOM" when with a "VGA/SVGA" signal with a vertical frequency 60 Hz and less. However, when a "VGA/SVGA" signal with a vertical frequency of more than 60 Hz is used, "CINEMA ZOOM" is not available. About Copyrights · When using the RESIZE function to select an image size with a different aspect ratio to a TV program or video image, the image will look different from its original appearance. Keep this in mind while choosing an image size. · The use of the Resize, Keystone Correction, Subtitle, or Overscan function to compress or stretch the image for commercial purposes/public displays in a café, hotel, etc. may be an infringement of copyright protected by law for copyright holders. · While watching non-widescreen images (4:3), if you use the RESIZE function to fill the screen or use the Overscan function to change the aspect ratio of a fixed-ratio input signal, parts of the outer edge of the image will be cut off or distorted. To watch original images as the producers intended, set RESIZE to "SIDE BAR" and Overscan to its default setting. 37 Basic Operation Operating with the Remote Control Shifting the Projected Image Vertically (Image Shift) For easier viewing, this function shifts the entire image projected on the screen up or down when projecting 16:9 images from DVD players or other connected devices. Press PIMAGE SHIFT. · The image moves up. IMAGE SHIFT buttons PICTURE MODE button IRIS button Press RIMAGE SHIFT. · The image moves down. Note · The Image Shift function operates when "Resize" is not set to "DOT BY DOT". · For details on Image Shift, see page 47. FREEZE button Switching the Iris Setting This function controls the quantity of the projected light and the contrast of the image. Press lIRIS. · Each time the button is pressed while the display is on, the mode is switched in the following order: HIGH BRIGHTNESS MODE MEDIUM MODE HIGH CONTRAST MODE Selecting the Picture Mode You can select the appropriate picture mode to best match the projected image you are watching. Press kPICTURE MODE. · When pressing kPICTURE MODE, the picture mode changes in the following order: Note · For details on Iris, see page 45. Freezing a Moving Image Standard Natural Movie2 Dynamic Movie1 1 2 38 Press hFREEZE. · The projected image is frozen. Memory Note Press hFREEZE again to return to the moving image from the currently connected device. · See page 43 for details on the picture mode. Menu Items The following shows the items that can be set in the projector. The selectable items vary depending on the selected input, input signals, or adjustment values. Items that cannot be selected will be greyed out. Main menu Sub menu Picture Mode "Picture" menu PAGE 1 Picture Picture Mode Contrast Bright Color Tint Sharp Red Blue Standard 0 0 0 0 0 0 0 INPUT 1 Picture Page 43 Page 43 Standard Natural Dynamic Movie1 Movie2 Memory Contrast Bright Color Tint Sharp Red Blue -30 -30 -30 -30 -30 -30 -30 +30 +30 +30 *2 +30 *2 +30 *2 +30 +30 SEL. /ADJ. RETURN ENTER END Page 43 PAGE 2 Picture Picture Mode CLR Temp BrilliantColorTM C. Progressive DNR IRIS Lamp Setting Reset SEL. /ADJ. RETURN 7500K 1 3D Progressive Level 1 High Brightness Bright Standard INPUT 1 CLR Temp Page 44 5500K 6500K 7500K 8500K 9300K 10500K BrilliantColorTM [0/1/2] Page 43 C. M. S. *1 Page 44 Progressive *2 Page 44 Single ADJ END DNR 2D Progressive 3D Progressive Film Mode OFF Level 1 Level 2 Level 3 High Brightness Medium Mode High Contrast Bright Eco + Quiet Page 45 IRIS "C. M. S. " C. - Value Reset R Y G C B M Reset SEL. /ADJ. RETURN 0 0 0 0 0 0 ENTER END Page 45 Lamp Setting Page 45 Reset *1 C. M. S. -Hue R Y G C B M Reset -30 -30 -30 -30 -30 -30 +30 +30 +30 +30 +30 +30 Useful Features Page 44 C. M. S. -Saturation Page 44 C. M. S. -Value Page 44 Reset *1 When a video signal, S-video signal, or component 480I/ 576I signal is input and the Progressive mode is set to "3D Progressive" or "Film Mode", the C. M. S. *2 Item that cannot be set when inputting an RGB signal through INPUT 5 or INPUT 6. 39 Menu Items (Continued) "Fine Sync" menu Fine Sync Clock Phase H-Pos V-Pos Reset Special Modes Auto Sync 0 0 0 0 1080I On INPUT 5 Main menu Fine Sync Clock -150 +150 Sub menu Page 46 Page 46 Phase -30 +30 Page 46 H-Pos -150 +150 Page 46 V-Pos -60 +60 Page 46 Reset Cur. RETURN ENTER END Special Modes Page 46 Auto Sync [On/Off] 1035I 1080I The resolution changes depending on the input signal. · The "Fine Sync" menu is not available for INPUT 3 or INPUT 4. Main menu Options 1 Page 46 Cur. [. . . ] 54, 55 Resize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36, 37 RESIZE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 RETURN button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]