User manual SHARP XV-Z30000 SETUP MANUAL

[. . . ] Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/ EEG. Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. Quest' apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC come emendata dalla direttiva 93/68/EEC. [. . . ] · See "Using the Adjustment Feet" on page 31 for adjusting the projector angle and "Variable Lens Shift Feature" on page 32 for adjusting the projected image position. -26 Switching the INPUT Mode Select the appropriate input mode for the connected equipment. INPUT buttons Press , or on the remote control to select the INPUT mode. on the projector, input mode · When pressing switches in order of INPUT 1 INPUT 2 INPUT 3 . "On-screen Display of INPUT Mode (Example) INPUT 1 mode Using Component Note · When no signal is received, "NO SIGNAL" will be displayed. When a signal that the projector is not preset to receive is received, "NOT REG. " will be displayed. · The INPUT mode is not displayed when "OSD Display" of the "Options" menu is set to " (OFF). (See page 47. ) " About the INPUT mode INPUT 1 (Component/RGB) INPUT 2 (S-Video) INPUT 3 (Video) Used for projecting images from equipment that sends component signals or RGB signals connected to the INPUT 1 terminal. Used for projecting images from equipment connected to the INPUT 2 terminal. Used for projecting images from equipment connected to the INPUT 3 terminal. INPUT 3 mode Using Video Using RGB INPUT 2 mode Using S-Video Basic Operation Volume buttons Adjusting the Volume Press or on the remote control to adjust the volume. Note · Pressing will lower the volume. · On the projector, the volume can be adjusted by pressing or . Volume buttons "On-screen Display -27 Image Projection Turning off the Sound Temporarily Press on the remote control to temporarily turn off the sound. Note · Pressing on. again will turn the sound back "On-screen Display MUTE button Turning the Power off (Putting STANDBY button the Projector into the Standby Mode) 1 Press on the projector or on the remote control, then press that button again while the confirmation message is displayed, to put the projector into the standby mode. "On-screen Display Note · If you accidentally pressed or and do not want to put the projector into the standby mode, wait until the confirmation message disappears. 2 Unplug the power cord from the wall outlet after the cooling fan stops. Info · Do not unplug the power cord during projection or cooling fan operation. The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode. This can cause damage due to rise in internal temperature, as the cooling fan also stops. -28 Correcting Trapezoidal Distortion When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. · You can also change the picture display mode by pressing on the projector. RESIZE button UNDO button -34 Input Signal Output screen image STRETCH (Default setting) SIDE BAR CINEMA ZOOM 4:3 aspect ratio 480I 480P NTSC PAL SECAM Letter box Squeezed 1080I 16:9 aspect ratio 720P Basic Operation VGA SVGA XGA 4:3 aspect ratio : Cutout area on which images cannot be projected. Note · "STRETCH" is fixed when 720P or 1080I signals are entered. -35 Using the Menu Screen The menu screens allow you to adjust the image and various projector settings. (The menu items differ depending on the input mode. ) The menu can be operated with the projector or with the remote control. Menu Selections (Adjustments) ', ", \, | buttons ENTER button 1 Press Note . MENU button · The "Picture" menu screen for the selected input mode is displayed. ENTER button UNDO button MENU button ', ", \, | buttons -36 2 Press \ or | to select the menu screen (icon) you want to set. Menu icon Menu screen Picture Fine Sync Options Language PRJ Mode Select the icon. · The menu icon for the selected menu screen is highlighted. Note · The "Fine Sync" menu is not available for INPUT 2 or 3. · For items on the menus, see the tree charts on pages 40 and 41. 3 Press ' or " to select the item you want to adjust. · The selected item is highlighted. Select the item. Note · If you want to adjust the item while viewafing the projected image, press ter selecting the item. Only the selected adjustment item will be displayed. When pressing ' or ", the following item ("Bright" after "Contrast") will be displayed. to return to the previous Adjustments and Settings 4 Press \ or | to adjust the item selected. · The adjustment is stored. 5 Press . · The menu screen will disappear. Adjust the item or make the setting. -37 Using the Menu Screen Menu Selections (Settings) ', ", \, | buttons ENTER button 1 Press Note . MENU button · The "Picture" menu screen for the selected input mode is displayed. ENTER button UNDO button MENU button ', ", \, | buttons 2 Press \ or | to select the menu screen (icon) you want to set. · The menu icon for the selected menu screen is highlighted. Menu icon Menu screen Picture Fine Sync Options Language PRJ Mode Select the icon. Note · The "Fine Sync" menu is not available for INPUT 2 or 3. · For items on the menus, see the tree charts on pages 40 and 41. -38 3 Press ' or " to select the item you want to set. Note · Press or \ to return to the previous screen. Select the item. 4 Press |. · The cursor shifts to the sub menu. · For some items, the sub menu cannot be displayed. In such cases, select the icon using \ or | to make a setting, then go to step 7. Sub menu 5 6 7 Press ' or " to select the setting of the item displayed in the sub menu. Press . · The item selected is set. Press . · The menu screen will disappear. Adjustments and Settings -39 Menu Items The following shows the items that can be set in the projector. "Picture" menu Main menu Picture Contrast Bright Color Tint Sharp Red Blue Reset -30 -30 -30 -30 -30 -30 -30 +30 +30 +30 +30 +30 +30 +30 Sub menu Page 42 Page 42 CLR Temp 5500K 6500K 7500K 8500K 9300K 10500K Standard Cinema1 Cinema2 Brighten Page 43 Note Gamma When using the INPUT 1 mode: · In the "Picture" menu of INPUT 1, "Color", "Tint" and "Sharp" are only displayed when "Signal Type" is set to "Component". [. . . ] 15 Replacing the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 RESIZE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 RGB cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]