User manual SHARP XV-Z7000E

[. . . ] Before using the LCD projector, please read this operation manual carefully. ENGLISH Important Information OPERATION MANUAL IMPORTANT For your assistance in reporting the loss or theft of your Colour LCD Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of "Supplied Accessories" on page 10. ENGLISH Model No. : XV-Z7000E Serial No. : WARNING: Intense light source. Do not look into the beam or view it directly. Be especially careful that children do not look directly into the beam. [. . . ] 3 If the screen is at an angle, the adjusters can be used to adjust the angle of the image. Returning the projector to its original position While holding the projector, press the foot releases and slowly lower the projector to its original position. · When an adjustment is made, the image may become distorted (keystoned), depending on the relative positions of the projector and the screen. CAUTION · Do not press the foot releases when the adjustment feet are extended without firmly holding the projector. · Do not hold the lens when lifting or lowering the projector. · When lowering the projector, be careful not to get your fingers caught in the area between the adjustment feet and the projector. Operation Reversed Image Setup Rear projection · Place a translucent screen between the projector and the audience. · Use the projector's menu system to reverse the projected image. (See page 34 for use of this function. ) Projection using a mirror · When the distance between the projector and screen is not sufficient for normal rear projection, you can use a mirror to reflect the image onto the screen. · Place a mirror (normal flat type) in front of the lens. · Project the normal image onto the mirror. · The image reflected from the mirror is projected onto the translucent screen. · Optimal image quality can be achieved when the projector is positioned perpendicular to the screen with all feet flat and level. CAUTION · When using a mirror, be sure to carefully position both the projector and the mirror so the light does not shine into the eyes of the audience. Ceiling-mount Setup · It is recommended that you use the optional Sharp ceiling-mount bracket for this installation. · Before mounting the projector, contact your nearest Sharp Authorised LCD Projector Dealer or Service Centre to obtain the recommended ceiling-mount bracket (sold separately). (AN-TK202 ceiling-mount bracket, AN-TK201 extension tube, AN-Z7T ceiling adaptors for AN-TK202 or AN-TK201. ) · When the projector is in the inverted position, use the upper edge of the screen as the base line. · Use the projector's menu system to select the appropriate projection mode. (See page 34 for use of this function. ) 18 Setting up the Screen Digital Keystone Correction · When the image is distorted due to the projection angle, the digital keystone correction function allows you to correct it. · The digital keystone correction can be made by pressing KEYSTONE, or by setting "Keystone" correction in the GUI menu. Projector ON/OFF POWER LAMP Remote control RGB/ INPUT 1 COMPONENT PICT MODE Using the KEYSTONE buttons 1 Press KEYSTONE to adjust the setting. TEMP. KEYSTONE INPUT PICT MODE INPUT 2 AUTO SYNC GAMMA 1 MENU S-VIDEO CLR TEMP VIDEO KEYSTONE FREEZE BACK ENTER Operation Projector ON/OFF POWER LAMP Remote control VOL Using the GUI menu 1 2 Press MENU. Press / to select "Options", and then press ENTER. Press / to select "Keystone", and then press ENTER. KEYSTONE PICT MODE POWER INPUT 2, 3 MENU MUTE BACK MENU BACK ENTER 3 1, 5 ENTER 4 (GUI) On-screen Display 5 To exit from the GUI, press MENU. · To reset the keystone setting, press BACK. · Straight lines and the edges of the displayed image may appear jagged, when adjusting the keystone setting. 19 Using the GUI (Graphical User Interface) Menu Screens Projector ON/OFF POWER Remote control 7 LAMP TEMP. VOL POWER 2, 4, 6 3, 5 MENU MUTE BACK MENU KEYSTONE INPUT PICT MODE This projector has three sets of menu screens (INPUT 1 or 2 (COMPONENT), INPUT 2 (RGB) and S-VIDEO or VIDEO) that allow you to adjust the image and various projector settings. These menu screens can be operated from the projector or the remote control with the following buttons. BACK ENTER 1, 8 ENTER (GUI) On-screen Display EXAMPLE INPUT 1 or 2 (COMPONENT) mode INPUT 2 (RGB) mode S-VIDEO or VIDEO mode 1 2 3 4 5 6 7 8 Press MENU to display the main menu. Press / to select an adjustment item in the main menu. Press / to select an adjustment item in the sub menu. Press ENTER to activate the selected adjustment item. [. . . ] These very sophisticated panels contain 480, 000 pixels ( RGB) TFTs (Thin Film Transistors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive TFTs within acceptable tolerances which may result in illuminated or inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit. Appendix Specifications are subject to change without notice. 46 FOCUS ZOOM ON/OFF POWER S-VIDEO INPUT LAMP TEMP. VIDEO INPUT KEYSTONE INPUT PICT MODE AUDIO INPUT BACK ENTER MENU 100-240V RS-232C INPUT 1 Y /COMPONENT CB CR AUDIO INPUT (INPUT 1, 2) INPUT 2 RGB /COMPONENT 47 Dimensions Side View 118 Rear View Top View 260 58 Bottom View Front View Units: mm Appendix 8 42 32 207 82 169. 5 (S-VIDEO, VIDEO INPUT) L R Glossary Active digital keystone correction Corrects keystone distortion caused when the projected image is not perpendicular to the screen. This method provides not only horizontal correction, but vertical as well, thus maintaining the original 4:3 aspect ratio and eliminating jag lines. [. . . ]