User manual SHARP XV-3300S OPERATION MANUAL

[. . . ] CONSUMER PRODUCT SAFETY ACT To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT "LIMITED WARRANTY" CLAUSE. ONLY WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. See bottom of actual set. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons. [. . . ] Page 50 Color Selected Standard Custom 1 [R] Red [Y] Yellow [G] Green [C] Cyan [B] Blue [M] Magenta Custom 3 Target Lightness Chroma Hue 30 30 30 +30 +30 +30 Reset (This Color) Reset (All Colors) View Settings -39 XV-3300S#Print#p31_39. p65 39 02. 10. 25, 7:29 PM Using the Menu Screen This projector has two sets of menu screens that allow you to adjust the image and various projector settings. You can operate the menus from the projector or remote control using the following procedure. Menu screen for INPUT 1, INPUT 2 or INPUT 5 RGB mode Menu screen for INPUT 3, INPUT 4 or INPUT 5 VIDEO Mode Menu Bar (Main Menu) Menu Bar (Main Menu) Menu Selections (Adjustments) ", ', \, | buttons ENTER button MENU button 1 Press . The menu screen is displayed. Note The "Picture" menu screen for the selected input mode is displayed. The on-screen display shown on the lower right is displayed when the INPUT 1, 2 or INPUT 5 RGB mode is selected. ENTER button MENU button ', ", \, | buttons "Menu Screen -40 XV-3300S#Print#p40_56. p65 40 02. 10. 25, 7:30 PM 2 Press \ or | to select the menu you want to adjust. Note For details on the menus, see the tree charts on pages 38 and 39. 3 Press " or ' to select the item you want to adjust. Note To display a single adjustment item, press after selecting the item. Only the menu bar and the selected adjustment item will be displayed. Then if you press ' or ", the following item ("Bright" after "Contrast") will be displayed. | Basic Operation Press or to return to the pre- vious screen. 4 Press \ or | to adjust the item selected. The adjustment is stored. 5 Press . The menu screen will disappear. -41 XV-3300S#Print#p40_56. p65 41 02. 10. 25, 7:30 PM Using the Menu Screen Menu Selections (Settings) " , ', \, | buttons ENTER button MENU button 1 Press . The menu screen is displayed. Note The "Picture" menu screen for the selected input mode is displayed. The on-screen displays shown on the lower right is displayed when INPUT 1, 2 or INPUT 5 RGB mode is selected. 2 Press \ or | to select the menu you want to adjust. Note For details on the menus, see the tree charts on pages 38 and 39. ENTER button MENU button ', " , \, | buttons M Menu screen 3 Press " or ' to select the item you want to set. Note Press to return to the previous screen. In some menus, select the icon using " ". Sub menu -42 XV-3300S#Print#p40_56. p65 42 02. 10. 25, 7:30 PM 4 Press |. The cursor shifts to the sub menu. Sub menu 5 Press " or ' to select the setting of the item displayed in the sub menu. Basic Operation 6 Press . The item selected is set. Note Some adjustment items will display a confirmation message. When setting an item, press \ or | to select "Yes" or "OK" and then press . Use to select "ON" or "OFF" for the item of "Eonomy Mode". 7 Press . The menu will disappear. -43 XV-3300S#Print#p40_56. p65 43 02. 10. 25, 7:30 PM Adjusting the Picture You can adjust the projector's picture to your preferences with the following picture settings. Adjusting Image Preferences Note First select "INPUT # Memory" when you want to save the "Picture" menu settings. See page 47 for details. Adjust the "Picture" menu on the menu screen. In NTSC or PAL60Hz, even if the 3D Progressive mode has been set, the threetwo pull down enhancement will be enabled automatically, when the film source has been entered. In PAL50Hz or SECAM, the two-two pull down enhancement will be enabled only in the Film Mode, when the film source has been entered. -46 XV-3300S#Print#p40_56. p65 46 02. 10. 25, 7:30 PM Picture Setting Function This function stores all items set in "Picture". Five settings can be stored separately in "Memory 1" to "Memory 5". Each stored setting is reassigned to each input mode (INPUT 1 to INPUT 5). Even when the input mode or signal is changed, you can easily select optimal settings from the stored settings. I When Saving: Select the Memory number to be saved or "INPUT # Memory" for each adjustment value in memory before setting on the "Picture" menu. Select "Picture Setting" in the "Picture" menu on the menu screen. For operating the menu screen, see pages 40 to 43. Description Settings of all items in "PicMemory 1 ture" can be stored for the reto spective input modes. The Memory 5 stored settings can be selected in any input modes. INPUT 1 Memory Besides "Memory 1" to "Memory 5", other settings to INPUT 5 Memory can be stored for each input mode. "INPUT 1-5 Memory" can be selected for each input mode. I When Recalling Saved Contents: When a saved memory number is selected, the contents of the "Picture" menu change to the adjustment values of the saved Memory number. Selected item Basic Operation PICTURE SETTING button Note The contents of "Picture Setting" can be butselected directly by pressing the ton. [. . . ] YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. Model Specific Section (In-Home Service) Your Product Model Number & Description: XV-3300S Projector (Be sure to have this information available when you need service for your Product. ) One (1) year parts and labor from date of purchase except for the Projector Lamp for which the warranty period is ninety (90) days from date of purchase. After the ninety (90) day warranty period on the Projector Lamp, parts and labor for a lamp replacement are the responsibility of the consumer. Cleaning of Optical System and/or replacement of any filter. [. . . ]