User manual SHARP XV380H OPERATION MANUAL

[. . . ] Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 12. ENGLISH Introduction Model No. : XV380H Serial No. : There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase. CONSUMER PRODUCT SAFETY ACT To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT "LIMITED WARRANTY" CLAUSE. ONLY WARNING: High brightness light source. [. . . ] This can cause damage due to the rise in internal temperature, as the cooling fan also stops. When connected to equipment such as an amplifier, be sure to turn off the power to the equipment connected first and then to the projector. -32 XV_Z200U_E_p29_43. p65 32 03. 10. 21, 4:13 PM KEYSTONE button Keystone Correction This function can be used to adjust the Keystone settings. Note For details about using the menu screen, see pages 38 to 41. ", ', \, | buttons 1 2 Press on the projector or on the remote control. Press / to select "H Keystone" or "V Keystone". Selected Item H Keystone V Keystone Reset Description Horizontally adjusts the keystone settings. Vertically adjusts the keystone settings. V and H Keystone adjustments are returned to the factory preset settings. KEYSTONE button ", ', \, | buttons Basic Operation 3 Press / to move the mark on the selected adjustment item to the desired setting. Note Straight lines and the edges of the displayed image may appear jagged, when adjusting the Keystone setting. When adjusting "H Keystone" and "V Keystone" at the same time, the values of adjustable angles for each setting become smaller. The adjustable value of the "V Keystone" becomes extremely small when "H Keystone" is made to be the maximum value. Keystone correction is disabled while the picture mode is set to "SMART STRETCH". (See page 35. ) Horizontal Keystone Correction Vertical Keystone Correction 4 To return to the normal screen, again. press -33 XV_Z200U_E_p29_43. p65 33 03. 10. 21, 4:14 PM Image Projection Placement of the Projected Image Using the Keystone Correction Place the projector at a distance from the screen that allows images to be projected onto the screen by referring to "Adjusting the Projection Distance" on pages 26 and 27. : Screen area 1 Project the test pattern of the Keystone correction function onto the screen. to return to the previous Press screen. Select the item. Adjustments and Settings 4 Press \ or | to adjust the item selected. The adjustment is stored. Adjust the item. 5 Press . The menu screen will disappear. -39 XV_Z200U_E_p29_43. p65 39 03. 10. 21, 4:14 PM Using the Menu Screen Menu Selections (Settings) ", ', \, | buttons UNDO button MENU button 1 Press . The menu screen is displayed. Note The "Picture" menu screen for the selected input mode is displayed. ENTER button ", ', \, | buttons UNDO button MENU button ENTER button 2 Press \ or | to display the other menu screens. The menu icon for the selected menu screen is highlighted. Menu icon Menu screen Picture Fine Sync Options Language PRJ Mode Select the menu icon. Note The "Fine Sync" menu is not available for INPUT 3 or 4. For items on the menus, see the tree charts on pages 42 and 43. -40 XV_Z200U_E_p29_43. p65 40 03. 10. 21, 4:14 PM 3 Press " or ' to select the item you want to set. Note Press to return to the previous screen. In some menus, select the icon us". ing " Select the item. 4 Press |. The sub menu is displayed. Sub menu 5 Press " or ' to select the setting of the item displayed in the sub menu. Sub menu 6 7 Press . Adjustments and Settings The item selected is set. Press . The menu screen will disappear. -41 XV_Z200U_E_p29_43. p65 41 03. 10. 28, 1:54 PM Menu Bar Items I INPUT 1 / 2 / DIGITAL INPUT Mode Main menu Picture ( ) Contrast Bright Color Tint Sharp Red Blue Reset CLR Temp 5500K 6500K 7500K 8500K 9300K 10500K Gamma Standard Cinema 1 Cinema 2 Cinema 3 White Emphasis [ON/OFF] Picture Setting Memory 1 Memory 2 Memory 3 Memory 4 Memory 5 Memory OFF Fine Sync ( ) Clock Phase H-Pos V-Pos Reset Special Modes Auto Sync Signal Info [ON/OFF] 30 15 30 30 30 15 30 30 640 480 720 480 480P Resolution Hor Freq Vert Freq 640 480 37. 5 kHz 72 Hz 0 0 0 0 0 0 10 10 10 10 10 10 PRJ Mode ( ) Front Ceiling Front Rear Ceiling Rear 30 30 30 30 30 30 30 30 30 30 30 30 30 30 Sub menu Main menu Language ( ) English Deutsch Espaol Nederlands Franais Italiano Svenska Portugus Options ( ) Lamp Timer (Life) OSD Display [ON/OFF] Signal Type RGB Component Background [None/Blue] Eco Mode [Eco/Standard] Auto Power Off [ON/OFF] Menu Position Center Upper Right Lower Right Upper Left Lower Left Menu Color [Opaque/Translucent] Note The resolution, vertical frequency and horizontal frequency figures displayed above are for example purposes only. "Color", "Tint", and "Sharp" do not appear when "RGB" is selected in INPUT 2 mode. "Signal Type" is not displayed when using INPUT 1. "Color", "Tint", "Sharp", "Clock", "Phase", "HPos", "V-Pos", "Special Modes" and "Auto Sync" cannot be used in the DIGITAL INPUT mode. "Clock", "Phase" and "Auto Sync" cannot be used in the Component mode. -42 XV_Z200U_E_p29_43. p65 42 03. 10. 21, 4:14 PM I INPUT 3 / 4 Mode Main menu Picture ( ) Contrast Bright Color Tint Sharp Red Blue Reset CLR Temp 5500K 6500K 3D Progressive 7500K 3D Progressive 8500K 3D Progressive 9300K 3D Progressive 10500K 3D Progressive Gamma Standard 3D Progressive Cinema 1 3D Progressive Cinema 2 3D Progressive Cinema 3 3D Progressive White Emphasis [ON/OFF] Picture Setting 3D Progressive Memory 1 Memory 2 3D Progressive Memory 3 3D Progressive Memory 4 3D Progressive Memory 5 3D Progressive Memory OFF 3D ProgrOFFessive Options ( ) Lamp Timer (Life) OSD Display [ON/OFF] Video System Auto PAL NTSC3. 58 SECAM NTSC4. 43 PALM PALN PAL60 Background [None/Blue] Eco Mode [Eco/Standard] Auto Power Off [ON/OFF] Menu Position Center Upper Right Lower Right Upper Left Lower Left Menu Color [Opaque/Translucent] 0 0 0 0 0 0 10 10 10 10 10 10 PRJ Mode ( ) Front Ceiling Front Rear Ceiling Rear 30 30 30 30 30 30 30 30 30 30 30 30 30 30 Sub menu Main menu Language ( ) English Deutsch Espaol Nederlands Franais Italiano Svenska Portugus Adjustments and Settings Note "Tint" cannot be used with PAL, SECAM, PAL-M, PAL-N or PAL-60. -43 XV_Z200U_E_p29_43. p65 43 03. 10. 21, 4:15 PM Adjusting the Picture You can adjust the projector's picture to your preferences with the following picture settings. On-screen Display Adjusting Image Preferences Note First select "Memory 1-5" or "Memory OFF" when you want to save the "Picture" menu settings. See page 47 for details. Adjust the "Picture" menu on the menu screen. [. . . ] Model Specific Section (In-Home Service) Your Product Model Number & Description: XV380H Projector (Be sure to have this information available when you need service for your Product. ) One (1) year parts and labor from date of purchase except for the Projector Lamp for which the warranty period is ninety (90) days from date of purchase. After the ninety (90) day warranty period on the Projector Lamp, parts and labor for a lamp replacement are the responsibility of the consumer. Cleaning of Optical System and/or replacement of any filter. Labor & materials required to remove and reinstall a suspended projector in installations not accessible with a standard (8' step) ladder or ceilings exceeding 12' in height. [. . . ]