User manual SHARP XV-Z1E

[. . . ] Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. Quest' apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC come emendata dalla direttiva 93/68/EEC. 89/336/ 73/23/ , µ µ 93/68/ . [. . . ] (See page 17 for removing and attaching the Swivel Stand. ) · Before mounting the projector, contact your nearest Sharp Authorised Projector Dealer or Service Centre to obtain the recommended ceiling-mount bracket (sold separately). (AN-TK202 ceiling-mount bracket, AN-TK201 extension tube, AN-60KT ceiling adaptors for AN-TK202 or AN-TK201) · When the projector is in the inverted position, use the upper edge of the screen as the base line. · Use the projector's menu screen to select the appropriate projection mode. (See page 42 for use of this function. ) -23 Using the Operation Buttons Selecting the Input Signal Source Press INPUT on the projector, INPUT 1, INPUT 2, INPUT 3 or INPUT 4 on the remote control to select the desired input mode. · When no signal is received, "NO SIGNAL" will be displayed. When a signal that the projector is not preset to receive is received, "NOT REG. " will be displayed. On-screen Display INPUT button INPUT 1 Mode INPUT 2 Mode Operation Buttons INPUT 4 Mode INPUT 3 Mode Adjusting the Picture Aspect Ratio This function allows you to modify or customize the picture display mode to enhance the input image. Depending on the input signal, you can choose NORMAL, BORDER or STRETCH image. Each time RESIZE is pressed, the picture mode changes as shown on the next page. 1 -24 Adjusting the Picture Aspect Ratio Input Signal NORMAL DVD/ VIDEO COMPUTER Image Type Projects the image fully on a screen while maintaining the aspect ratio. Output screen image BORDER Projects the image on the screen whose surrounding areas are cut out to make a 4:3 screen while maintaining the aspect ratio. STRETCH Projects the image on the screen whose upper and lower areas are cut out to make a 16:9 screen while the image is horizontally enlarged. * * 4:3 aspect ratio Operation Buttons 480I 480P 540P NTSC PAL SECAM VGA (640×480) SVGA (800×600) XGA (1024×768) Letter Box * * -- * Squeezed 16:9 image * Squeezed 4:3 image * 16 : 9 aspect ratio 720P 1080I -- * * Mode for projecting an image with the original aspect ratio without cutting any portions. : Cutout area on which images cannot be projected. : Area on which the image is not included in the original signals. -25 Using the Menu Screen Basic Operations This projector has two sets of menu screens that allow you to adjust the image and various projector settings. These menu screens can be operated from the projector or the remote control with the following procedure. 1, 7 64 2, 3, 5 On-screen Display INPUT 1 (COMPONENT) or 2 (COMPONENT or analog RGB) mode INPUT 3 or 4 (VIDEO) mode 1 2 1 2 Basic Operation 3 3 4 1 Press MENU. The "Picture" menu screen for the selected INPUT mode appears. 2 Press / to display the other menu screen, if you want. 2 Press 2 / to select a specific adjustment item. 3 Press / to move the mark of the selected adjustment item to the desired setting. 4 To exit the menu screen, press MENU. · To reset all adjustment items, select "Reset" on the "Picture" menu screen and press ENTER. · "Tint" cannot be used with PAL, SECAM, PAL-M, PAL-N or PAL-60. -29 Adjusting the Picture Adjusting the Colour Temperature This function allows for selecting the desired colour temperature from six settings. With the lower value selected, the projected image becomes warmer, reddish and incandescent-like while with the higher value, the image becomes cooler, bluish and fluorescent-like. Description of Colour Temperature 4 2, 3 1, 5 1 Press MENU. The "Picture" menu screen appears. / to select "CLR Temp", and then press 3 Press / to select the desired colour temperature setting. On-screen Display 4 Press ENTER to save the setting. 5 To exit the menu screen, press MENU. · Values on "CLR Temp" are only for general standard purposes. The less the value is set to, the warmer, reddish, incandescent-like the image becomes. The more the value is set to, the cooler, bluish, fluorescent-like the image becomes. Basic Operation Emphasising the Contrast This function emphasizes the bright portions of images to obtain a higher contrast image. Description of White Emphasis Selected item Description For emphasizing the bright portions of images For disabling "White Emphasis" ON ( 2, 3 1, 4 OFF ( ) ) 1 Press MENU. The "Picture" menu screen appears. [. . . ] 26 Exhaust ventilative hole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 F Focus ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 I INPUT buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 INPUT 2 COMPONENT/RGB port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]