User manual SHERWOOD CD5505

[. . . ] Improper extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe. For your safety, if in any doubt about the effective earthing of the power point, consult a qualified electrician. PAN-EUROPEAN UNIFIED VOLTAGE All units are suitable for use on supplies 220-240 V AC. Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. [. . . ] STANDBY indicator When this unit is turned off, this indicator lights up. 3. STEREO indicator When FM broadcasts are reproduced in stereo sound, this indicator lights up. 4. TUNED indicator When a station of sufficient strength is tuned in, this indicator lights up. 14. STEREO/MONO button When listening to FM broadcasts, press this button to select the STereo mode or the MONO mode depending on the strength of broadcst signal. 5. RDS indicator When RDS broadcasts are received, this indicator lights up. 15. AUTO PRESET button Press this button to automatically search for FM stations and to store them in the memory. 6. Remote sensor This receives the signals from the remote control unit. 16. AUTO TUNING button Press this button to search for a station of sufficient strength automatically. 7. Fluorescent display This displays operation status, frequency, RDS information, etc. 17. NUMERIC(0~9) buttons Press these buttons to specify the preset number of the station directly to be recalled or stored in the memory. 8. DIMMER button Each time this button is pressed, the brightness of the fluorescent display changes as follows : → ON → dimmer → OFF 18. Tuning/ Preset mode • Each time the BAND button on the front panel is pressed, the band and the FM mode change as follows : → FM STereo (STEREO indicator lights up) → FM MONO → (STEREO indicator goes off) AM 9 ENGLISH TX-5505(G)_ENG_100819_TX-5505(G)_ENG 2010-08-19 오후 5:31 페이지 10 Manual tuning • Manual tuning is useful when you already know the frequency of the desired station. • After selecting the desired band (and the tuning mode in case of using the TUNING/PRESET knob), rotate this knob one by one slowly or press the TUNING UP(+)/ DOWN(-) buttons repeatedly until the right frequency has been reached. TUNING / PRESET Manual presetting • You can store up to 40 preferred stations in the memory. ENGLISH 1. Tune in the desired station with auto or manual tuning. 2. Press the TUNING/PRESET knob or the MEMORY button. or TUNING / PRESET or • Press and hold down the TUNING UP(+)/DOWN(-) buttons to reach quickly the right frequency. Auto presetting • Auto presetting function automatically searches for FM stations only and stores them in the memory. FM S T 8 9 . 1 0 M Hz P0 2 1. While listening to FM broadcasts, press the AUTO PRESET button. AUTO PRESET • The preset number flickers for several seconds. ■On the front panel or 3. Rotate the TUNING/PRESET knob to select the desired preset number(1~40) and press this knob. TUNING / PRESET TUNING / PRESET • Then “FM AUTO PRESET” flickers for several seconds. • If “FM AUTO PRESET”goes off, press the AUTO PRESET button again. 2. When “FM AUTO PRESET” flickers, press the AUTO PRESET button again. • The station has now been stored in the memory. • A stored frequency is erased from the memory by storing another frequency in its place. • If the preset number does not flicker or disappears, start again from the above step 2. • Then “SEARCH” flickers and the tuner starts auto presetting. • To stop auto presetting, press this button again. • Up to 40 FM stations can be stored. ■Notes : • FM stations of weak strength cannot be memorized. • To memorize AM stations or weak stations, perform “Manual presetting” procedure with using “Manual tuning” operation. 4. [. . . ] • If no station is found, “NO PTY” flickers for several seconds. 13 ENGLISH TX-5505(G)_ENG_100819_TX-5505(G)_ENG 2010-08-19 오후 5:31 페이지 14 TP search • Use this function to automatically search and receive the stations broadcasting the traffic program. ADJUSTING THE BRIGHTNESS OF THE FLUORESCENT DISPLAY ENGLISH 1. DIMMER Perform the steps 1 and 2 in “RDS search” procedure on the previous page to select “TP”. or • Then “SEARCH > TP” is displayed on the RDS menu for several seconds. • When the RDS menu is not displayed, repeat again from the above step 1. 2. Start TP search. • Each time the DIMMER button is pressed, the brightness of the fluorescent display changes as follows : → ON → dimmer → OFF • In the display OFF mode, pressing any button will cancel the display OFF mode for several seconds to display the operation status. • The tuner automatically searches for stations broadcasting the traffic program. • If the signal is too weak or there are no stations broadcasting the traffic program, “NO TP” flickers for several seconds. Displaying RDS information • While listening to RDS broadcasts, • Each time this button is pressed, the display mode changes as follows: Radio Program Program Clock Station → Service name → Type → Time → Text → name (RT) (PS) (PTY) (CT) * * : Possible only when the preset station has a name. [. . . ]