User manual SHERWOOD HSB-6501

[. . . ] Introduction READ THIS BEFORE OPERATING YOUR UNIT This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. FCC INFORMATION(FOR U. S. A. ) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] · Please be care the environmental aspects of battery disposal. · The unit shall not be exposed to dripping or splashing for use. · No objects filled with liquids, such as vases, shall be placed on the unit. · Do not let insecticides, benzene, and thinner come in contact with the set. · Never disassemble or modify the unit in any way. §s Notes on the AC power cord and the wall outlet · The unit is not disconnected from the AC power source(mains) as long as it is connected to the wall outlet, even if the unit has been turned off. · When disconnecting the power cord from the wall outlet, always pull the plug, not the power cord. · Disconnect the plug from the wall outlet when not using the unit for long periods of time. · The wall outlet shall be installed near the unit and shall be easily accessible. 4 CONTENTS Introduction · READ THIS BEFORE OPERATING YOUR UNIT · SAFETY INSTRUCTIONS | 3 · ACCESSORIES | 5 Part Names and Functions · FRONT PANEL | 6 · BACK PANEL | 6 · REMOTE CONTROL | 6 · REMOTE CONTROL OPERATION RANGE · LOADING BATTERY | 7 | 2 |7 System Connections · CONNECTING TV AND THE SOURCE EQUIPMENT WITH COMPONENT VIDEO OUTS · CONNECTING TV AND THE SOURCE EQUIPMENT WITH HDMI OUTS | 10 · CONNECTING MULTI-ROOM SYSTEM KIT | 11 Operations | 12 Definition of Terms | 13 | 14 |8 Troubleshooting Guide Specifications | 15 ACCESSORIES 1. · In addition, when you connect the OPTICAL OUT to this unit, this unit can output the digital signals as they were input from the HDMI OUT connector, too. · When making the component video connections, connect "Y" to "Y", PB" to "PB"(or "B-Y", "CB") and "PR" to "PR"(or "R-Y", "CR"). §s Connecting the display equipment with the HDMI IN connector · The HDMI connection can carry uncompressed digital video signals and digital audio signals. · If your display equipment (TV, projector, etc. ) has the HDMI IN connector, connect it to the HDMI OUT connector of this unit using the supplied HDMI cord. · Among the HDMI IN connector equipped TV or projector, etc. , some do not support audio output(for examples, projectors). In such a case, make the digital audio connection(and the analog audio connection if needed) between the source equipment and the display equipment(or A/V amp, receiver). §s Connecting the display equipment with the DVI IN connector · If your display equipment has the DVI IN connector compatible with DVI and High-bandwidth Digital Content Protection (HDCP), connect it to the HDMI OUT connector of this unit using a commercially available HDMIDVI converter cord. Since the HDMI-to-DVI connection cannot carry audio signals, you should make the digital audio connection(and the analog audio connection if needed) between the source equipment and the display equipment (or A/V amp, receiver). §s Notes : · This unit supports HDMI(High Definition Multimedia Interface) version 1. 1 · This unit supports HDCP(High-bandwidth Digital Content Protection), a protection system for digital video. If not, the image will not be output properly. · This unit supports 480p(576p), 720p, 1080i as the resolution of video signals. Therefore, when making COMPONENT VIDEO connections, be sure to output the progressive video signals (480p or 576p) from your source equipment. If your source equipment outputs the interlaced video signals (480i or 576i), the HDMI OUT of this unit will output no video signals or abnormal video signals. [. . . ] · Poor connection at AC wall outlet or the outlet is dead or off. REMEDY · Connect cord securely. · Check the outlet using a lamp or another appliance. · Select the input source correctly. · The HDMI OUT connector does not output the video and audio signals of it. [. . . ]